Gl616 Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

Best Seller

Genuine Whirlpool part

Dryer Drum Belt 92-1/4" 4-Rib

4.9 (1867)

By: Whirlpool

Part Number: 341241

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

Problem	How the belt solves it
Drum won’t turn	Transfers motor rotation to drum
Loud squealing / thumping	Replaces stretched or frayed belt
Burning-rubber smell	New belt stops slippage & heat build-up
Damp clothes / long cycles	Restores correct drum speed & airflow

DIY install — about 15 minutes

Unplug dryer; remove lint screen housing & front panel.
Release belt tension at idler pulley; lift drum slightly to slide old belt off.
Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
Re-assemble, run test cycle - enjoy quiet, consistent tumbling.

This part fixes the following symptoms

Heat stays on after drum has stopped
Will not tumble
Touchpad does not respond
No heat or not enough heat

Do-It-Yourself Stories from Customers like You Broken dryer belt Bob B. • St Louis , MO • September 12, 2015

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

$14.95

Compare At:: $17.79
You Save:: $2.84

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Gas Valve Coil Kit

4.9 (1836)

By: Whirlpool

Part Number: 279834

Dryer won't heat or flame shuts off after 15 seconds? Gas valve coils control gas flow to the burner. Takes about 30 minutes to replace both coils.

This part fixes the following symptoms

Timer will not advance
No heat or not enough heat
Shuts off too soon
Takes too long to dry

Do-It-Yourself Stories from Customers like You Flame to dry clothes would go out after about a minute and wouldn't reignite Wendell M. • Brown Deer , WI • June 19, 2014

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

$28.43

Compare At:: $34.12
You Save:: $5.69

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Idler Pulley

4.9 (463)

By: Whirlpool

Part Number: WP691366

Idler pulley maintains belt tension in your dryer drum assembly. Replace if the wheel is cracked, bracket is broken, or pulley has worn bearings.

This part fixes the following symptoms

Will not tumble
Takes too long to dry

Do-It-Yourself Stories from Customers like You Thumping/vibrating/rattling pretty bad fixed 100%! Doug P. • Durham , NC • November 15, 2015

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

$15.95

Compare At:: $18.82
You Save:: $2.87

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Igniter Kit

4.9 (401)

By: Whirlpool

Part Number: 279311

Dryer not heating or won't dry clothes? This igniter kit lights the gas burner. Moderately easy DIY repair with video guide—replaces failed igniters.

This part fixes the following symptoms

No heat or not enough heat
Takes too long to dry

Do-It-Yourself Stories from Customers like You 11 year old kenmore elite gas drye stopped working initial diagnosis: burner would light but would shut off in 3 or 4 minutes Jay W. • Dallas , TX • April 05, 2015

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

$32.64

Compare At:: $42.42
You Save:: $9.78

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Drive Motor

4.9 (249)

By: Whirlpool

Part Number: 279827

Dryer won't start or stops mid-cycle? A worn drive motor is often the cause. This motor turns the drum and circulates air. Moderate DIY repair.

This part fixes the following symptoms

Will not tumble
Noisy
Shuts off too soon

Do-It-Yourself Stories from Customers like You High pitched squeal: maybe a roller wheel maybe a bad felt bearing on drum maybe a rubbing fan wheel or just a burned out motor! Bruce K. • Pikeville , KY • September 06, 2014

My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again. Last month, my wife said it stopped again and its making a loud noise, but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse). I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,... Read more

$97.47

Compare At:: $131.61
You Save:: $34.14

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Door Latch Kit

4.9 (307)

By: Whirlpool

Part Number: 279570

The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.

Symptoms of needing to replace the door latch kit include:

Difficulty in closing or latching the washer door
Door opening unexpectedly during the wash cycle
Leaks or water seeping due to an improper door seal
Excessive wear or damage to the latch components

Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

This part fixes the following symptoms

Door won't close
Shuts off too soon
Doesn't shut off
Takes too long to dry

Do-It-Yourself Stories from Customers like You Dryer door latch worn out Kathy M. • San Diego , CA • February 22, 2015

When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ... Read more

$9.55

Compare At:: $13.85
You Save:: $4.30

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Motor Pulley

5.0 (46)

By: Whirlpool

Part Number: WP8066184

The Motor Pulley is an OEM part for Whirlpool dryers, connects the dryer motor to the drum belt, enabling the drum to turn and efficiently dry your clothes. This pulley is crucial for the smooth operation of the dryer, ensuring that the belt is tensioned correctly and runs smoothly without slipping or causing wear.

Causes of a bad Motor Pulley include wear and tear from regular use, a buildup of lint and debris that can interfere with its operation, or a malfunctioning dryer motor that puts undue stress on the pulley.

Symptoms of a bad Motor Pulley include:

Unusual noises coming from the dryer, such as squeaking or grinding
The dryer drum failing to turn even though the motor is running
The dryer taking longer than normal to dry clothes, which can occur if the pulley is not providing proper tension to the belt

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You Broken motor pulley Michele D. • Jefferson , MA • December 11, 2015

Replaced pulley and belt. Read more

$40.95

Compare At:: $48.73
You Save:: $7.78

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Door Switch

4.9 (103)

By: Whirlpool

Part Number: W10820036

The Washer Door Switch is an OEM part for Whirlpool washing machines. This component is crucial for ensuring the washer operates safely by detecting whether the door is open or closed. The door switch prevents the washer from starting or continuing its cycle when the door is open, and it allows the machine to function only when the door is securely closed.

Symptoms of a failing Washer Door Switch include:

The washer not starting or stopping unexpectedly during a cycle
Error codes related to door closure issues displayed on the washer's control panel
The washer door not locking properly or the lock mechanism not engaging
The washer continuing to operate with the door open

Causes of a bad door switch can include wear and tear from frequent use, damage from repeated opening and closing of the door, electrical faults such as short circuits, or physical damage from mishandling or impact.

This OEM Whirlpool part is also compatible with some models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore.

This part fixes the following symptoms

Will not drain
Pumps but will not spin
Timer will not advance
Doesn't shut off

Do-It-Yourself Stories from Customers like You Sometimes the washer wouldn't start the wash cycle when the fill cycle was done it would just sit until the lid was picked up or bumped Eugene N. • Roswell , NM • August 28, 2016

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

$22.53

Compare At:: $32.43
You Save:: $9.90

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Lint Screen

4.9 (154)

By: Whirlpool

Part Number: 339392V

Captures lint and debris during drying to maintain airflow and prevent vent clogs. Replace if torn, frayed, or handle is broken. Verify fit by model number.

This part fixes the following symptoms

Takes too long to dry

Do-It-Yourself Stories from Customers like You Noisy & inefficient Richard M. • Indianapolis , IN • December 06, 2016

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

$55.95

Compare At:: $67.14
You Save:: $11.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Leveling Foot

5.0 (50)

By: Whirlpool

Part Number: 49621

The Dryer Leveling Foot is an OEM part for Whirlpool dryers. It is designed to support and stabilize the dryer by allowing adjustments to the height and leveling of the unit. Proper leveling ensures the dryer operates smoothly and efficiently, reducing vibrations and preventing unwanted movement during cycles.

Causes of a bad leveling foot can include wear and tear from regular use, damage from moving the dryer, or breakage due to heavy loads and stress. Over time, the threads on the leveling foot can wear out, or the foot itself can become cracked or deformed.

Symptoms of a bad leveling foot include:

Dryer rocking or wobbling during operation
Unusual noises or vibrations
Difficulty in adjusting the dryer's height
Visible damage or wear on the leveling foot

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Do-It-Yourself Stories from Customers like You Took the base off the washer and dryer and they had no feet on them. Paula S. • Onalaska , WA • March 22, 2014

Bought the leveling feet and screwed them in the bottom and they work great. Read more

$7.24

Compare At:: $7.63
You Save:: $0.39

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Appliance Touch-Up Paint

4.9 (33)

By: Whirlpool

Part Number: 72017

Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.

Do-It-Yourself Stories from Customers like You Chipped paint Thomas S. • Middletown , DE • September 03, 2014

Touch up paint Read more

$11.78

Compare At:: $14.02
You Save:: $2.24

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Lp Conversion Kit

4.9 (61)

By: Whirlpool

Part Number: 49572A

The LP Conversion Kit is an OEM component for Whirlpool and KitchenAid gas dryers. It allows conversion from natural gas to liquid propane fuel operation. Over time in gas-powered dryers, improper gas/air mixture causes part wear like weakened burner components. This is risky if overlooked but converting to an alternative fuel safely remedies.

Causes relate to unavoidable deterioration from gas combustion stresses. Conversion using this kit prevents hazardous gas leaks or explosions.

Symptoms involve:

Diminished or unsafe heat levels from burners
Gas leaks which exacerbate safety risks over time

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Do-It-Yourself Stories from Customers like You Needed to convert gas dryer to propane Ken B. • Foresthill , CA • June 12, 2014

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

$33.70

Compare At:: $40.10
You Save:: $6.40

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Appliance Spray Paint

4.9 (35)

By: Whirlpool

Part Number: 350930

Color: White. Size: 13 oz can. Acrylic appliance aerosol can spray paint.

The Appliance Spray Paint is an OEM part for Whirlpool appliances, designed to provide a quick and effective way to touch up or completely refinish the exterior of various appliances. This specialty spray paint is formulated to adhere to metal surfaces, offering a durable and resistant finish that can withstand the routine wear and tear of kitchen environments, including heat, moisture, and everyday use.

The primary reason for using such a specialized paint is to maintain or restore the aesthetic appeal of your appliances while protecting them from further damage.

Symptoms needing for Appliance Spray Paint include:

Scratches, chips, or rust spots on the appliance's exterior that can lead to further damage or corrosion if left untreated
A desire to refresh or update the appearance of the appliance without the need for complete replacement
Discoloration or fading of the original finish due to age, exposure to sunlight, or cleaning agents

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Do-It-Yourself Stories from Customers like You Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015

Replaced It With New One Read more

$24.95

Compare At:: $29.94
You Save:: $4.99

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Door Switch Lever

4.9 (37)

By: Whirlpool

Part Number: WP691581

The Door Switch Lever is an OEM part for Whirlpool dryers. It plays a vital role in ensuring the dryer only operates when the door is securely closed by engaging with the door switch to signal the door's status.

Causes of a bad door switch lever can include normal wear and tear from repeated use, physical damage from accidental impact, or deformation from heat and humidity inside the dryer. A faulty lever can prevent the dryer from starting or stopping correctly.

Symptoms of a bad door switch lever include:

Dryer not starting
Dryer stopping mid-cycle
Door not latching properly
The dryer continuing to run with the door open

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part fixes the following symptoms

Won't start
Doesn't shut off

Do-It-Yourself Stories from Customers like You The lever to the door switch broke. Valerie M. • Rochester , NH • April 02, 2014

First, I rooked on YouTube for a video on how to fix it. The video brought me to a very helpful video with a link to your website. We have had this dryer since we bought the house 10 years ago and the thought of buying something new, that wasn't made as well was a dreaded thought. I went on the website, entered the model number of my dryer and then a search link for a parts search. Not knowing the part number, I was able to find the exact thing I needed. It was amazing and so easy! Had... Read more

$7.70

Compare At:: $8.47
You Save:: $0.77

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Front Bearing And Seal Kit

4.8 (14)

By: Whirlpool

Part Number: 279264

Replaces worn dryer front bearing and seal that cause squealing or scraping noise. Essential for smooth drum rotation. Confirm fit with your model.

This part fixes the following symptoms

Noisy

Do-It-Yourself Stories from Customers like You Noisy & inefficient Richard M. • Indianapolis , IN • December 06, 2016

$67.95

Compare At:: $81.54
You Save:: $13.59

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Top Lock

4.9 (28)

By: Whirlpool

Part Number: WP18776

The Top Lock is an OEM component for Whirlpool electric and gas dryers. It secures the outer metal cabinet door during drying cycles for safety and ventilation. This lock provides a method for releasing and latching the door tightly when shut.

Symptoms of a failing top lock may include:

Inability to fully close or properly latch the dryer door
Accidental opening from deficient locking during operation
Difficulty manipulating the lock due to worn or broken parts

Causes related to normal wear of moving parts through frequent use over several years. Deformation from excessive exterior impacts could also damage locking mechanisms.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You Clothes dryer drum stopped rotating Edward J. • Eclectic , AL • February 20, 2015

Located model number and went to Appliance Parts Pros.com to check the repair instructions on belt and motor. Used the suggestions to diagnose problem as a broken belt. I also ordered two top locks to replace the originals that were very brittle plastic that broke when I opened the dryer. Ordered the parts on Presidents Day, and received the parts the next day. The dryer was back in service in 24 hours. Read more

$12.95

Compare At:: $15.28
You Save:: $2.33

IN STOCK

Ships Monday Guaranteed

Add to Cart

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Gl616 Parts

Dryer Drum Belt 92-1/4" 4-Rib

Why this belt?

Fixes these common dryer problems

DIY install — about 15 minutes

Dryer Gas Valve Coil Kit

Dryer Idler Pulley

Dryer Igniter Kit

Dryer Drive Motor

Door Latch Kit

Motor Pulley

Door Switch

Dryer Lint Screen

Leveling Foot

Appliance Touch-Up Paint

Lp Conversion Kit

Appliance Spray Paint

Door Switch Lever

Dryer Front Bearing And Seal Kit

Top Lock

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Gl616 Parts

Why this belt?

Fixes these common dryer problems

DIY install — about 15 minutes

We respect your privacy

Manage consent preferences