Gss25jfmbwwlsrcss Parts

The Ice Bucket Dispenser Cover is an OEM part for GE refrigerators. It acts as a shield for the ice bucket, maintaining the insulation around the ice and ensuring the ice remains frozen while preventing freezer burn. 

Causes of a bad ice bucket dispenser cover can include physical damage from handling or excessive frost buildup, which can warp or crack the plastic. 

Symptoms of a bad Ice Bucket Dispenser Cover include:

• Increased ice melting or clumping
• Frost or ice accumulation in inappropriate areas of the freezer
• Visible damage to the cover, such as cracks or warping

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This ice dispenser deflector mounts in the freezer door chute to guide cubes or crushed ice into your glass. Replace a cracked or missing deflector to reduce scatter and keep ice flowing where you want it.

• Directs ice down the dispenser chute toward the glass
• Helps contain spray and bounce-back of cubes
• Restores proper flow when the original deflector is cracked, warped, or missing
• Common symptoms: ice misses the glass, ice scatters on the floor, visible damage to the deflector

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Access the dispenser area per your model's instructions and note the deflector's orientation
• Transfer any screws or clips from the old part; avoid forcing plastic tabs
• Restore power and test ice dispense to confirm proper direction and clearance

This 15 uF capacitor kit supports an AC motor by providing the phase shift needed to start and run smoothly. Replacing a weak or failed capacitor can help resolve hard-start or no-start issues and restore consistent performance. What it does

• Stores and releases energy to help a single-phase AC motor start and maintain proper torque
• Common symptoms include humming or buzzing without starting, repeated clicking, intermittent starting, or warmer-than-normal temperatures
• Visual clues of failure may include a swollen or cracked housing
• Matched 15 uF rating supports correct motor operation per the original design

• One 15 uF capacitor

• Disconnect power before servicing; verify the capacitor is fully discharged before handling
• Note wire positions; move one lead at a time to the new capacitor
• Match the microfarad (uF) rating to the original part for proper performance
• Secure the capacitor using the existing bracket/strap and route wires away from heat and moving parts

The Dispenser Lever is an OEM part for GE refrigerators. This lever activates the dispensing mechanism, allowing you to release water or ice from the refrigerator's dispenser.

Causes of a bad dispenser lever can include regular wear and tear, damage from excessive force or mishandling, and breakage due to frequent use. 

Symptoms of a bad dispenser lever include:

• The dispenser lever not returning to its original position
• Difficulty in activating the dispenser
• The lever feeling loose or unresponsive
• Water or ice not dispensing when the lever is pressed

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Restore reliable ice dispensing with this ice dispenser bucket. It holds the icemaker's ice supply and interfaces with the dispenser drive so cubes or crushed ice can feed smoothly through the chute when you press the dispenser lever.

• Holds ice produced by the icemaker and positions it for dispensing
• Engages with the drive to move ice toward the chute
• Can help resolve weak/no ice dispensing or frequent ice jams
• Common failures include cracks, broken tabs, or worn drive engagement points

• Unplug the refrigerator and wear cut-resistant gloves before servicing
• Remove the old bin from the freezer, empty it, and slide in the new bucket; ensure the drive coupling fully engages
• Restore power, allow the icemaker to produce ice, and test dispensing

Color: white. It measures about 16 inches wide by 2 inches high by 2 inches deep.

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

The Pan Cover Front Gasket is an OEM part for GE refrigerators. This gasket provides a seal for the front edge of the refrigerator's crisper or pantry drawer pan cover, preventing cold air from escaping and ensuring that the contents remain at the optimal temperature for freshness.

Common causes of a bad gasket include regular wear and tear, exposure to food spills, or accidental damage from frequent opening and closing of the drawer.  

Symptoms of a bad pan cover front gasket include:

• The drawer not sealing properly, leading to temperature fluctuations
• Visible cracks, tears, or warping of the gasket
• Increased condensation or frost buildup in the drawer area
• Food items spoiling faster than usual

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

This lower light shield is the clear lens that covers the lower refrigerator lamp, diffusing brightness and protecting the bulb from contact. Replace a cracked, missing, or yellowed cover to restore even lighting and a clean, finished look.

• Diffuses the lower compartment light for softer, more even illumination
• Acts as a barrier to help prevent accidental contact with the bulb and splashes
• Replace if the cover is cracked, discolored, warped, missing, or won't stay secured
• Installs over the lower light using the appliance's existing tabs or screws

• Disconnect power to the refrigerator before servicing
• Allow the bulb to cool before handling the lens
• Release retaining tabs or remove screws carefully; avoid over-flexing the plastic
• When reinstalling, do not overtighten to prevent cracking the shield

The Door Handle is an OEM part for GE refrigerators. This part provides a secure and comfortable grip for opening and closing the refrigerator door.  

Causes of a bad door handle can include regular wear and tear, accidental impact, or repeated use, which can lead to cracks, breaks, or loosening of the handle.  

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Difficulty in opening or closing the door
• Visible cracks or breaks in the handle
• The handle detaching from the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Color: white. Measures about 18 inches wide by 4 inches high by 8 inches deep.

Color: white. It measures about 15 inches wide by 1 inch deep.