Gx2fhdxvbo3 Parts

Replaced relay and capacitor attached to compressor Read more

I searched online for replacement parts and Appliance Parts Pros had the part in stock. Before I ordered the part, I watched the video to see if I could handle the repair. I ordered the part and soaked the gaskets with warm water in the tub. The old gaskets had a much simpler setup, so no cutting was involved. I simply pulled the old gasket out of the track without issues, and installed the new one with finger pressure. Per the video, I took both doors off. However, due to the design, I could... Read more

Left new gasket on the table overnight so it could stretch out. Removed the door. Temporarily replaced it with plastic and tape. Pulled off old gasket. Cleaned surfaces with decreaser and wiped dry with paper towels and alcohol. Inserted new gasket. Replaced door. Read more

A bit of online research and some component testing narrowed my issue down to either a faulty ice maker or a bad supply valve. Appliance Parts Pros had both of these, at reasonable prices, so I purchased and replaced both items. I recommend watching online videos to get a sense of what to do, and how to go about doing it. The repairs were relatively easy, other than this being a bottom freezer model hence the ice maker was difficult to access: I removed the freezer door (four screws) to get... Read more

First, I watched your VERY HELPFUL videos showing exactly how to remove and assemble the parts. I removed the salvageable parts from the old shelf frame and reassembled it. Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

They are easily replaced with no tools. Read more

• Freezer section too warm

The fan has a very thin wire in it's coil, and when that wire breaks, you need a new fan. In a previous repair, i noticed that an ice build-up had dislodged the wiring on my fan and severed the coil winding. I was able to undo the winding a couple of turns and get it working again. But more recently, the fan stopped and there was no repairing it. So i ordered a new fan from AppliancePartsPros.com and it got here in very good time. The new fan was slightly different as the prongs seemed to be... Read more

• Fridge too warm
• Noisy

I determined that the motor that drives the damper valve that allows cold air into the refer was noisy. I ordered the replacement part from AppliancePartsPro.com. It arrived within 3 days and I changed the units out, which took about 10 minutes total. All is quiet with the refer now. Read more

Having never fixed a fridge before, I did a little research. The unit was not old & the cooling system was operating. Observing the frozen ice inside, I diagnosed it as the heat rod and/or it's thermostat as bad. I contacted ApplianceParts Pros, who assisted in confirming my theory. IMPORTANT NOTE: the sales advisor Joyce was truly an intelligent, knowledgable professional, NOT some "burger-order taker" usually encountered. This alone speaks VOLUMES. Subsequently, the parts arrived... Read more

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

• Door won't open or close

Looked for parts online that were worn and compared prices. Best price was appliance part pros. Ordered and received in 2 days and easily replaced worn parts. Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more