Jds960aap Parts

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This surface burner spark igniter creates the electric arc that lights the gas flame on your cooktop or range. Replacing a worn or cracked electrode restores reliable ignition and helps resolve hard-to-light burners and intermittent sparking.

• Provides a high-voltage spark at the surface burner to ignite gas
• Mounts to the orifice holder beneath the burner head
• Failure symptoms include burner not lighting, needing a match, or intermittent/weak spark
• Common issues: chipped/cracked ceramic insulator or damaged terminal/lead

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; remove grates, burner caps, and heads to access the orifice holder
• Transfer the ignition lead, install the new electrode, and route the wire away from heat and sharp edges
• Ensure the tip is positioned near the burner as designed; verify spark and ignition before reassembly

This screw-and-washer fastener is a factory-size 8-18 x 5/16 hardware piece used to secure appliance panels and components. Replace stripped, rusty, or missing hardware to restore a tight, rattle-free fit and proper alignment. What it does:

• Fastens sheet-metal panels, brackets, and small components in the appliance cabinet
• Replaces lost, stripped, or corroded screws to maintain secure mounting
• Helps reduce vibration, buzzing, or rattling from loose parts
• Useful when the original hardware is missing or no longer holds securely

• Includes 1 screw-and-washer fastener (8-18 x 5/16)

• Disconnect power; shut off gas and water supplies if applicable
• Match the fastener to the original location; sizes can vary by application
• Start threads by hand to avoid cross-threading; use an appropriately sized driver
• Tighten snugly without overtightening to prevent stripping sheet metal

For screws order: WP7101P485-60.

This is a Whirlpool range control panel. It houses the display, user interface buttons, and has space for temperature control knobs. With extended use, the buttons on a control panel may wear out or stop responding to user input.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the old control panel in place. Remove the screws from each side of the old control panel to disconnect it, then carefully remove any boards or other components installed within the panel. Once it has been completely removed, the new control panel can be installed in its place.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This rocker switch controls the exhaust function on the appliance's ventilation system. It restores reliable on/off control of the blower when the original switch becomes worn, sticks, or fails. What it does:

• Provides on/off control for the exhaust/blower circuit
• Replaces a faulty or intermittent rocker that prevents the vent from operating correctly
• Helps address symptoms such as blower won't start, won't shut off, or only works when the switch is jiggled
• Restores proper tactile feel if the old switch is loose, cracked, or stuck

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Access the control panel and note wire positions or take a clear photo
• Transfer wires one at a time to the new switch; ensure terminals are fully seated—do not pull on the wires
• Reassemble panels, restore power, and test exhaust operation

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:

• Moves air across the heater, through the drum, and out the vent to remove moisture
• Helps maintain proper airflow and temperature inside the dryer
• Common failure symptoms: reduced or no airflow at the exterior vent, longer dry times, unusual scraping/thumping or vibration from the blower area, or overheating/shutoff
• Cracked fins or a stripped hub can cause the wheel to slip on the motor shaft

• 1 blower wheel

• Disconnect power and turn off gas supply before servicing
• Access the blower housing per your model's service instructions; remove the retaining hardware and replace the wheel in the same orientation
• Clean lint from the blower housing and vent path; inspect the motor shaft and blower seal for wear
• Reassemble and verify the wheel spins freely without rubbing; check airflow at the exterior vent

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.

This safety thermostat monitors internal temperature and opens the circuit if the appliance overheats. Replacing a failed high-limit thermostat restores heat and helps protect controls, wiring, and nearby components from thermal damage. What it does:

• Monitors temperature and interrupts power to the heating circuit if an unsafe temperature is reached
• Helps prevent overheating damage to internal components
• When failed open, can cause no heat or cause the unit to shut off during high-heat operation
• At room temperature it should read closed/continuous; an open reading indicates replacement is needed

• 1 high-limit thermostat

• Disconnect power at the breaker (and shut off gas supply if applicable) before servicing
• Access location varies by model; commonly mounted to the oven cavity, plenum, or rear panel
• Transfer wires one at a time and mount the thermostat flush to its surface or bracket
• After replacement, verify proper airflow/cooling and address any root causes of overheating

Color: Black. For biscuit order 98008169. For white order WP98008544.

This burner spark igniter produces the electrical arc that lights the gas flame on your range or cooktop. Replacing a worn electrode restores quick, dependable ignition and helps stop continuous clicking when a burner won't light.

• Generates the high-voltage spark that ignites the gas at the burner
• Works with the ignition module to light the burner when the knob is turned
• Common symptoms of a failing igniter: clicking but no flame, no visible spark, burner lights only with a match, intermittent or delayed ignition
• Restores fast, reliable lighting performance at the burner

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Access the electrode at its burner location; note its position and gap relative to the burner before removal
• Handle the ceramic insulator carefully and reuse original mounting hardware if applicable
• Reconnect the spark wire securely, reassemble, and test for proper spark and ignition

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This spark module generates high-voltage pulses to ignite the surface burners on your gas cooktop or range. Replacing a failed module helps restore fast, reliable ignition when you turn a burner knob.

• Converts line voltage into high-voltage pulses for the surface igniters to light gas
• Sends spark when a burner switch calls for ignition; multiple electrodes may spark together by design
• May help address: no spark on all burners, intermittent or weak spark, burners that click but won't light
• Continuous rapid clicking can also occur with a failed module or wet/stuck burner switches

• Disconnect electrical power and shut off gas before servicing
• Access the module under the cooktop/top panel or behind the control area; label or photograph wiring and move leads one at a time to the new module
• Mount the new module securely in the original location; ensure all connectors are clean, dry, and fully seated
• Restore power and test each burner for proper spark and ignition

This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.

• Secures wire lugs to a 10-32 terminal stud for a solid electrical connection
• Restores proper clamping force when the original nut is stripped, corroded, or missing
• Helps address loose/burned terminal connections, heat discoloration, or intermittent power at the block
• Suitable for terminal block and similar 10-32 stud applications on compatible appliances

• Disconnect power at the breaker or unplug the appliance before servicing
• Inspect the terminal block, studs, and wiring for heat damage; replace any damaged components
• Clean threads and start the nut by hand to avoid cross-threading; tighten firmly without overtightening
• If the stud turns while tightening, hold it with an appropriate tool to protect the block

6,000 BTU. Color: Coal matte black. Measures about 2 inches in diameter.