Ksrl25fxms02 Parts

Purchase a new one and installed per your video on Youtube. Great and easy. Read more

I replaced the drive shaft, coupling and seal and now it works well. The videos were a big help. Read more

Removed the back cover to access the fan area. Clean the area with brush and vac first. Unplugged the Refrigerator. Used a socket set with 1/4" socket. Had an extended and a standard socket. Removed the condensate plastic drain from the bottom of the refrigerator to have more access to the fan. Unplugged the fan motor. Removed the two screws holding the fan in place. Removed the fan unit from the condenser side of the bracket. Place new fan on the fan and installed exactly the way I removed the... Read more

Touch up paint Read more

Replaced It With New One Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more

Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more

Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more

Replaced filter cap with new one. The minor challenge was to find a method of pulling the filter out of refrigerator (which is normally done by pulling on the filler cap. The filter was recessed to far into the refrigerator for me to be able attach the new cap. I had to find another tactic to remove the filter. The solution was to look at the replacement filter to notice where two slots were located at the end of the filter. I then used a paint can opener (found at most paint stores) to slip... Read more

Followed the video you provided. Read more

• Leaking

The drain pan (Tray-Evaporator Pan) was cracked in 2 places. We had to remove the front panel. Loosen the bracket that holds the water filter. Take off the back panel and disconnect the bracket that holds the selenoid. It was not necessary to unhook the water lines, just the bracket. It was not easy to remove the old pan and get the new one in, but holding the water filter, with the bracket intact, as far to the left side of the refrigerator as possible gave us the room to get the pan in. ... Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more

I noticed Ice maker Quit for the third time in 15 years so I decided to buy another Ice maker, I installed it and NO ice still?? Well I went after the other problem thinking if it does not get cold enough maybe ice maker won’t work. I ordered Defrost Switch, Heater and Evaporator Fan just to be safe. I replaced all three, the fan was noisy, the heater OHM’d ok but I replaced it as did the defrost switch, I put it back together, the Freezer got to 0 degrees and the frig got to 38 degrees so I... Read more