We use cookies and similar tools for site analytics and advertising. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
Replaced the tube and the clamp Read more
Fix washer overfilling or not filling properly with a new water level pressure switch. Controls fill shutoff and cycle transitions. DIY repair.
Replaced both, the water level switch and the water level hose. Watched the how to video first on your site and made the repair easy. Read more
Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.
Took off the back of the top pushed the switch forward and lifted it out after I unplugged it. Put the new switch in the opposite of how I took it out, plugged in the wires put the back on and finished my laundry. Read more
Washer won't start or spin? A broken lid switch actuator prevents the safety switch from engaging. This plastic striker restores proper operation in 5 minutes.
Replace the broken switch Read more
One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Leaking water at the tub ring during fill? This lower water injector channels incoming water into the tub. Simple 30-minute DIY repair with basic tools.
An easy fix for the most part. I had no idea what I was doing, but glad I bought both upper and lower injectors. Not sure why these are separate parts? Cheap plastic. I did not get the hose clamp because I didn't think I would need it. You probably do, so go ahead and just order it or grab one if you have one laying around. Mine is hooked up without it for now which I'm sure I will regret later but I needed to get our washer running immediately due to a bed bug situation in our house. Read more
Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
Fix a washer that won't advance through cycles, fills but won't spin, or stops mid-cycle. This timer controls wash, rinse, and spin sequences. 30-minute DIY repair.
Replaced the main timer / control. Read more
Washer making noise or controls not stopping correctly? This stop lug limits component movement to prevent over-travel. Simple snap-in repair.
I emailed appliancepartspros.com with what my problem was and they informed me what was wrong they gave me a part number to order, tools needed and a brief explanation how replace the seal. they also have online video's for different repairs. I watched the video for lip seal(part # 207843) replacement.I also had to remove the brake assembly in order to replace the seal so I watched that video also. I went online and got the part numbers for items I needed to make my repairs.Just follow the... Read more
This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.
Bought a new hose and took one small cover off the back of machine, used pliers to remove clamp, took off old hose, put on new, replaced clamp, replaced cover and was done. Five minutes tops. Read more
This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.
Removed lid sanded down all rust spots, taped over the printed instructions on the inside of the lid, washed with alcohol and spray painted with appliance white epoxy paint. Replaced the plastic hinge-balls and one of the lid support/bumper grommet. It was actually easier to install the lid than removing it; used a small amount of grease to hold both balls in place, by holding the lid vertical and placing the left side to the inserted ball and then pushing the right side down. The lid slides... Read more
This is a rubber gasket that sits inside the water inlet hose connection on your washing machine. It creates a watertight seal between the hose fitting and the water supply valve to prevent leaks. Replace this gasket if you notice water dripping from the hose connections at the back of the washer.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Mounting bolt secures the tub and internal components in your laundry center. Replace if stripped, rusted, or missing to restore stable assembly fit.
Purchased and installed new tub bearing and seals. Decided to replace the tub bolts as well, since I had it apart. Now if I could just find a new outer tub (which the manufacturer has discontinued). Appliance parts pros has a great "how to" video which made it simple! Read more
This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.
We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more
Connects suspension spring to washer frame to support the tub. Replace if hook is broken, worn, or missing to restore proper tub suspension and alignment.