Le4127w2 Parts

Ordered a new one from the website, matched the model and the picture Read more

Use the videos on this website here and you can repair most brands. Many are duplicate in design. 1. Unplug the machine. 2. Move it away from a confined area to get more room. 3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet. 4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you... Read more

Unplugged unit from power. Removed two sheet metal screws and lower front panel, removed two sheet metal screws and door panel (disconnected three door switch wires and two light wires - noted the connected position of each wire ); removed three self-tapping screws and black plastic hot air outlet to fan duct from lower end of front bulkhead; removed sheet metal screws and front bulkhead; removed two sheet metal screws from dryer top panel and raised top up and back on rear hinge brackets;... Read more

Replaced Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

• Will not tumble

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

• Too hot

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

The front panel clips needed to be replaced as they were bent and the some of the tabs for the bearing ring had broken off. Very pleased with the price, the parts and the quick delivery. Thank you. Read more

• Will not agitate
• Pumps but will not spin
• Will not tumble
• Noisy

Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more

Changed parts Read more

• Door won't close

I chatted with a rep on Appliance Parts Pros and found out which parts I needed for my model of dryer. Ordered the 2 clips that held the door closed. They arrived the next day!! My dryer was very different than the video but we were able to figure out which screws to remove. The old clips popped out and the new ones popped in. Took about 30 minutes because of there being a top and bottom clip to remove and replace and line up the door parts to screw the screws back in. It works great!! I... Read more

Replaced It With New One Read more

Touch up paint Read more