Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't spin or spins slowly? This motor mount roller and spring kit restores proper spin performance. Moderately easy DIY repair with video guide.
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more
Water won't shut off or keeps filling when washer is unplugged? Replace the water inlet valve. Easy 30-minute DIY fix for most models. Video available.
Ordered a new inlet water valve . Super fast delivery ordered on a Wednesday afternoon was here Thursday morning , standard shipping , I was impressed !! Removed the old valve , installed the new , checked for leaks no issues , washer is back on line and my Honey is very happy with me . Read more
Prevents backflow of drain water into fresh water supply. Mounts on top of washer. Replace if cracked, leaking, or damaged to restore proper drainage.
We ordered parts from appliance parts pros and I fixed it. Read more
If your dryer won't stay lit or shuts off after a few minutes, the gas limiter may be faulty. This regulator controls safe gas flow to the burner.
Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more
Dryer door won't stay closed? This door latch kit includes strike and mounting hardware. Easy 10-minute repair—just remove front panel screws.
Took off front cover of drier, removed old part and just snapped in new part. Read more
Washer won't start or keeps blowing fuses? The lid check switch ensures your washer only runs when the lid is closed. Easy DIY repair in under 30 minutes.
First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more
Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure. This kit includes the catch and hardware. 10-minute DIY fix.
Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more
Secures washing machine hoses to prevent leaks in the water system. Replace if damaged, corroded, or connections are loose. Verify fit by part number.
Washer leaking during fill? A cracked or clogged injector nozzle is often the culprit. This part directs water into the tub. Simple 20-minute DIY fix.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Dryer won't heat or start? This thermal fuse cuts power when temperatures get too high. Test with a multimeter for continuity. Easy DIY repair.
Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more
Carries wastewater from your washer to the household drain. Replace if cracked, split, or leaking at connections to pump or drain standpipe.
I decided to order the siphon break kit (siphon break, washer and clamp included), a new hose, and clamp (for the bottom hose connection) as the hose was original and well over 15 years old. I probably could have used the old clamp, but decided to get a new one in case there were problems with the old during removal. The video provided by A.P.P was helpful in giving confidence this was a task that could be done by myself. As was shown in the video, the hose connection to the siphon break had a... Read more
Replaces broken or cracked siphon break assembly on your washer. Installs on back panel where drain hose connects. Needed when elbow becomes brittle.
Ordered Siphon Break Kit. Speedy shipping, thank you. Attached video shows how to remove front of washer to access screws to loosen top of washer to access siphon break from inside washer cabinet. http://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/siphon-break-Maytagwasher.html Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Seals the tub cover to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the tub. Confirm fit with your model number.
Replaced mounting stem and tub bearings Read more
Secures drum rollers, brackets, and panels in your dryer. Replace if stripped, corroded, or missing to restore safe, rattle-free operation. Confirm fit.
It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more