Lte524ddz2 Parts

The Front Bearing and Seal Kit is an OEM replacement part for Whirlpool dryers. This kit includes the front bearing and seal for the dryer drum, which work together to provide smooth operation and prevent premature wear.

Causes of a bad front bearing and seal can include regular wear and tear from normal use, heavy loads that place extra strain on the bearings, or debris accumulation causing increased friction.

Symptoms of issues include:

• Noisy or grinding sounds coming from the drum area
• Vibration noticed during the operation
• Difficulty turning or rotating the dryer drum by hand
• Reduced efficiency and longer drying times

This OEM replacement kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.   

Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.

Symptoms of a bad start switch include:  

• Heating elements or tumble cycles that will not engage properly
• Dryer fails to operate or stops mid-cycle unexpectedly
• Control panel appears non-responsive to selections  
• Error codes related to ignition or power delivery faults

Note: This dryer push-to-start switch has 2 terminals.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models. 

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

The Gearcase Oil Seal is an OEM part for Whirlpool washing machines. This seal is located in the gearcase, preventing oil from leaking out while ensuring the internal components are properly lubricated. The kit contains two plastic seals that slide over the shaft to create a tight oil barrier.

Causes of a bad oil seal can include wear and tear over time, exposure to high friction and heat, or accidental damage during maintenance. A faulty oil seal can lead to oil leaks, which may cause further damage to the gearcase and other components.

Symptoms of a bad gearcase oil seal include:

• Oil leaks underneath the washer
• Loud noises during operation
• Washer not spinning or agitating properly
• Visible wear or damage to the seal

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Thermal Fuse is an OEM component for Whirlpool dryers. As a one-time-use safety component, the thermal fuse monitors heat levels and acts as an overload protector. This is a one-time use fuse that cannot be reset.

Causes of a bad thermal fuse include exposure to excessively high temperatures from a failure or blockage of another component like the venting system.

Symptoms of a bad thermal fuse are:

• The dryer fails to heat at all
• Randomly cutting out during cycles
• Visible damage or melting of the fuse housing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Neutral Drain Kit is an OEM part for Whirlpool washing machines. This kit facilitates the neutral drain function, which allows the washer to drain water without spinning the tub, ensuring efficient water removal before the spin cycle begins.

Causes of a bad neutral drain kit can include wear and tear over time, mechanical failure of the components, or damage due to improper installation or handling. A faulty neutral drain kit can lead to draining issues, affecting the overall performance of the washing machine.

Symptoms of a bad neutral drain kit include:

• Washer not draining properly
• Extended or incomplete drain cycles
• Water remaining in the tub after the drain cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Lid Strike is an OEM part for Whirlpool washing machines. This small yet essential component ensures that the washer lid is securely latched, allowing the machine to operate safely and effectively. The lid strike interacts with the lid switch, enabling the washer to detect when the lid is closed and allowing the washing cycle to proceed.

Over time, the lid strike can become worn out or damaged due to regular use, accidental force, or misalignment. A faulty lid strike can prevent the washing machine from recognizing that the lid is closed, thereby hindering the operation of the machine.

Symptoms of a bad lid strike include:

• The washer not starting or stopping mid-cycle
• Error messages indicating the lid is open when it is closed
• Difficulty in latching the lid securely
• The lid strike appearing broken or misaligned

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Timer is an OEM replacement part for Whirlpool washers. It is an electronic component that controls the duration of each wash cycle. The timer is located behind the control panel of the washer.

Causes of a faulty timer can include stripped internal gears or disconnected wiring terminals from use over the years.

Symptoms of a bad timer include:

• Inability to start or stop cycles at the correct times  
• Unexpected shutoff or prolonged run times 
• Failure to load, wash, rinse, or spin functions

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Seal Shaft is an OEM replacement part for Whirlpool washing machines. Internally situated where the tub meets the transmission case, it prevents liquid and debris from the transmission and gearcase.

Causes of replacement consist of normal friction fatigue after repeated cycles. Mineral chunking within grooves and notches also gradually increases operating torque if left unattended.

Symptoms involve:

• Excessive noise and vibration emerging from the transmission area
• Water leaks developing between tub and case
• Gradual mechanical burden decreasing agitator action

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

The Seal is an OEM part for Whirlpool washing machines. This part provides a tight seal around the washer shaft, preventing water from leaking out of the tub during the wash cycle.

Causes of a bad shaft seal can include wear and tear over time, exposure to harsh detergents or cleaning agents, or damage from foreign objects that may have gotten into the washer. 

Symptoms of a bad shaft seal include:

• Water leaking from the bottom of the washing machine
• Excessive noise during operation
• Visible damage or wear on the seal
• Wet spots or puddles under the washer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Thermostat is an OEM part for Whirlpool dryers. It plays a critical role in regulating the temperature inside the dryer by cycling the heating element on and off to maintain the desired level of heat. This ensures that clothes are dried efficiently and safely.

Common causes of a bad thermostat include electrical malfunctions, overheating, or wear and tear over time. These issues can prevent the thermostat from accurately controlling the temperature, leading to drying inefficiencies or potential safety hazards.

Symptoms of a bad Thermostat include:

• The dryer not heating up
• Overheating or extremely high temperatures
• Clothes taking too long to dry
• The dryer shutting off prematurely

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Clutch Retaining Clip is an OEM part for Whirlpool washing machines. This clip secures the clutch assembly, which is essential for the proper engagement and operation of the washer's transmission.

Causes of a bad retaining clip can include repeated mechanical stress, corrosion, or accidental damage during maintenance or repair.

Symptoms of a bad retaining clip include:

• Washer not spinning or agitating properly
• Unusual noises during operation
• Excessive vibrations or movement
• Washer failing to complete cycles correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Heating Element is an OEM component specifically designed for Whirlpool brand electric dryers. It contains coils that produce hot air used throughout drying cycles.

Symptoms of a failing heating element include:  

• Slow drying times as clothing takes longer than usual to dry fully
• Excess condensation inside the dryer drum
• Damp items after an entire cycle 

Potential causes involve typical coil wear from repeated heating and cooling over many years. Mineral scale buildup or poor ventilation can diminish heating efficiency as well.

Compatible models include some brands produced by KitchenAid, Maytag, Amana, and Kenmore.

The Terminal Block is an OEM replacement part for Whirlpool dryers. It is responsible for distributing electricity to key components that control drying operations.

Symptoms of a bad terminal block include:

• The dryer not heating up properly or failing to achieve the desired temperature
• Components like lights or timers not functioning
• Strange buzzing or humming noises coming from the dryer

Causes of terminal block failure can be worn or damaged wiring terminals, loose connections due to normal vibration, or corrosion buildup over several years of use.

This terminal block is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore dryer models. 

Please note: Please note that this part does not include the wires, screws, and nuts. They must be ordered separately. For the complete block assembly use 279320.

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head