Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Basically rebuilt the washer from the ground up. Spent more money than a new washer but we have been so happy with the way this machine has worked over the last 19 years figured it would be money well spent. Read more
Color: White. For gray order 2206781. Front load washer dispenser lid. If you need the pins to attach the lid order the long pin WP6-912678 and the short pin WPY912679
After much internet research (primary YouTube) as to why my Maytag Neptune washing machine's spin cycle stopped working, I ordered the parts I needed to fix it. Sure enough, it was a failed wax motor and a blown control board at fault. After replacing both parts, we have a functioning washing machine again. While I was at it, I replaced the soap dispenser's bezel and lid since they were deteriorating and now we have a "new" washer! I also replaces the thermostat in the matching dryer and we... Read more
Dryer not heating? This heater relay controls power to the heating element. Quick DIY fix when cycles stay cold. Includes testing instructions.
Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:
I have a Maytag washer that is over 30 years old and still runs like a top. When the siphon break got destroyed in our move, I was able to find a replacement kit that fixed our problem. I found a video on UTube that showed us just what to do. I'm delighted I didn't have to buy a new washer since the quality of new ones doesn't hold a candle to the quality of my Maytag. Read more
This sensor is connected to the washer's tub and monitors water levels by detecting air pressure changes in the pressure tube. Replace if the washer overfills, underfills, or displays water level error codes.
I verified that there were no drain line obstructions. Checked the ohms across the pump motor. Ran the washer through the diagnostics test. Determined that the main control board must be the problem. Washer would run until the spin cycle. It would pump down and continue pumping even though there was no water. Would not advance to spin. It would time out and flash the nd code. I was able to get it to run by shutting it off, turning back on and selecting the spin only button. Thought I would try... Read more
Installed a new water velve but there was still some leakage, discovered that there was three holes in the door boot....will order a new one. Read more
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Ultimately, I blew through the hose that attaches to the pressure switch. There was initially significant back pressure and then it blew free. Prior to this, I replaced the pressure switch, the main control board, and the pump. All of those were likely unneeded, but unfortunately no web links indicated this particular fix and Amana support was no help. I was very satisfied with the cost of parts on this site and the instructional video links. Just wish I had know to check for clog in the... Read more
Front load washer door boot seal, comes with drain plug and clamp.
I used the instructions from some of your previous customers. When I was ready to pull the inner tub from the outer tub, it pulled very hard. The front bearing had been HOT and really marked the shaft. The SEAL appeared to be almost plastic, not much left. I removed the seal from the Front bearing. This model had the original type seal with the plastic spacer behind the seal and in front of the front bearing.. BE SURE TO NOTE HOW THE PLASTIC SPACER CAME OUT--feet on spacer toward the... Read more
Replace your washer's cracked or worn outer tub assembly. Includes ball bearing, rear bearing, water deflector, and lip seal. Essential structural part.
This dryer electronic control board has a two digit display and is used on some Maytag and Crosley brands.
The washer baffle set consists of curved plastic or metal lifters inside the wash drum that agitate clothes during the wash cycle. These components lift and tumble clothing to ensure thorough cleaning and prevent tangling. Replace them when clothes don't get clean properly, you hear scraping noises, or the baffles are cracked or missing.
Disconnected dryer power cord; Removed 2 front door screws and 2 screws on opposite side; removed door and front dryer panel; removed 2 screws holding top dryer panel and lifted top; took pictures of 5 wire connections prior to disconnecting them; removed front tumbler panel and removed Duct Assembly Outlet. Vacuumed lent from dryer and cleaned and vacuumed out blower assembly. Installed new blower seal on new duct assembly and installed combined assembly. Reassembled dryer, reconnected dryer... Read more
This rubber grommet seals and cushions the connection where the front baffle attaches to your washer. It prevents water leaks and reduces vibration noise during operation. Replace this grommet if you notice water leaking from the front panel area or if there's excessive noise during wash cycles.
To start my Maytag MAH8700AWW started making a thumping noise and was eating at the door boot seal. I started doing research and found some folks changed the shocks and springs but had no luck so I thought I would wait it out to see if it would get worse. Sure enough it started to get so loud I thought it was going through the wall. At this point I decided to tear into it. Come to find out the main shaft assembly had broken two out of the three arms that are the main supports for the inner... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.