Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer door won't stay closed? This door latch kit includes strike and mounting hardware. Easy 10-minute repair—just remove front panel screws.
Took off front cover of drier, removed old part and just snapped in new part. Read more
Secures washing machine hoses to prevent leaks in the water system. Replace if damaged, corroded, or connections are loose. Verify fit by part number.
We ordered parts from appliance parts pros and I fixed it. Read more
Washer leaking during fill? A cracked or clogged injector nozzle is often the culprit. This part directs water into the tub. Simple 20-minute DIY fix.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Dryer won't heat or start? This thermal fuse cuts power when temperatures get too high. Test with a multimeter for continuity. Easy DIY repair.
Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more
Replaces broken or cracked siphon break assembly on your washer. Installs on back panel where drain hose connects. Needed when elbow becomes brittle.
Ordered Siphon Break Kit. Speedy shipping, thank you. Attached video shows how to remove front of washer to access screws to loosen top of washer to access siphon break from inside washer cabinet. http://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/siphon-break-Maytagwasher.html Read more
Carries wastewater from your washer to the household drain. Replace if cracked, split, or leaking at connections to pump or drain standpipe.
I decided to order the siphon break kit (siphon break, washer and clamp included), a new hose, and clamp (for the bottom hose connection) as the hose was original and well over 15 years old. I probably could have used the old clamp, but decided to get a new one in case there were problems with the old during removal. The video provided by A.P.P was helpful in giving confidence this was a task that could be done by myself. As was shown in the video, the hose connection to the siphon break had a... Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Secures drum rollers, brackets, and panels in your dryer. Replace if stripped, corroded, or missing to restore safe, rattle-free operation. Confirm fit.
It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more
Factory spring kit for washer motor assemblies. Restores proper belt tension and motor positioning. Replace when springs are missing, broken, or stretched.
Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
Seals the gap between drum and bulkhead to maintain airflow and drying performance. Replace when worn to reduce noise and prevent snagging. Verify fit.
Ordered and replace all moveable parts to stop squeaking. Dryer performing like new!!! Read more
Secures components with constant tension to prevent looseness and vibration. Replace if broken, fatigued, or missing. Verify fit with your model number.
Replaced them. Read more
Seals blower housing to prevent air leaks and lint escape. Replace when you notice lint buildup in your home or reduced drying efficiency. Confirm fit with your model number.
Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more
Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Rubber foot installs beneath washer leveling legs to provide stability and protect flooring. Replace if cracked, dried, crumbling, or missing.
Replaced dried crumbling rubber foot. Cleaned inside and outside of dryer before installing igniter cleared vent hose. Leveled unit installed dryer igniter. Fired it up.Runs Great Now. Read more