Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Plastic drum baffle that lifts and tumbles clothes during drying. Replace if cracked, broken, detached, or missing from inside your dryer drum.
I installed it my self by watching your video Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Connects your dryer to the wall outlet to supply household electricity. Replace a damaged, frayed, or overheated cord to restore safe power connection.
Thanks to you, all went well. No problems. Read more
Timer won't advance and dryer runs continuously? This 4-cycle timer controls cycle selection and timing. DIY repair typically takes 15-20 minutes.
Part ordered installed (easy), fixed problem for two loads of wash. Dryer then ran but did not heat. Researched on web and tested thermal interrupt fuses. Ordered (easy install) and now all is well. In the course of the fix it became apparent that the exhaust vent had rotted open on the portion resting on the floor. This was blowing hot air into and below the dryer and opened the fuse. All fixed, all is well. appliancepartspros.com Rated as a ten!!!!! Read more
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
It was very easy to fix after watching your video.. Read more
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.
Replaced belt and idler arm, just to be safe. Read more
Exterior cover that restores your dryer's finished appearance and shields internal components. Replace if cracked, broken, or missing to maintain protection.
Replaced broken coupling with new coupling Read more
Secures the lint duct assembly inside your dryer to prevent rattling and keep items from reaching the blower wheel. Replace if bent, broken, or missing.
There's a metal piece that the lint filter pushes down into that got bent a bit I guess and ended up skewering the lint filter. I got it loose but couldn't get the metal piece to stay where it was supposed to be to operate without catching the lint filter. I think it's there to prevent things like socks from hitting the blower wheel. When the new part came in I had to take the front cover off the blower wheel. It was easier than I thought, just three bolts/screws. Don't bother taking off... Read more
Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.
Changed the old parts with the new ones. Unscrewed one side. The other side was broken Put the new parts together and screwed back into place Done. Everything works Read more
Terminal box encloses the power cord connection area at the rear of your dryer. Replace if cracked, damaged, or worn to protect wiring and connections.
Replaced the part labeled #14 box. Read more
Secures the rear bulkhead to the washer tub, reducing vibrations. Replace if damaged by water exposure, stripped threads, or rusted from age.
Springs were broken and back bracket was bent I replaced the bracket and all four Springs including the vertical one. I removed the cabinet as shown in the video. Then with a pair of vise grips's removed the springs one by one and replace them. The bracket was rusted And bent i used a quarter inch socket with a quarter inch ratchet to remove the screw. Due to the rust i used penetrating oil the screw. Read more
Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.
Two 6-foot braided inlet hoses with 90-degree ends for washer water connections. Replace kinked, aged, or worn hoses to restore proper filling.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Lint trap won't slide in all the way or gets stuck? A damaged or obstructed lint chute assembly is usually the cause. Straightforward 30-minute repair.
I replaced the chute and screen - I am very mechanical and have good tools - it took me less than 30 minutes - would take many people longer but it is a straightforward project Read more
Fix a washer that won't stop filling, overfills, or doesn't fill properly. This water level pressure switch senses water levels and signals the control board.
I looked at the May tag parts diagrams to get an idea of the part(s) I may need to replace. I submitted the problem to Appliancepartspro and got a very quick response from them (thank you) confirming what part I needed. Replaced the water level switch/sensor and done.. Read more