Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces dim, flickering, or burnt-out bulbs in refrigerators, ovens, and microwaves. Restores interior lighting for visibility. Verify fit with model.
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more
Oven won't heat or takes too long to preheat? A weak or failed igniter is the most common cause. Easy DIY repair, typically completed in under 15 minutes.
I used the little video clip shown under the part and replaced it myself. Read more
Mice nesting in your oven? Replace damaged insulation wrap to restore heat retention and cooking performance. Wraps around oven cavity. DIY-friendly.
Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more
Oven not heating properly or showing F3 error? The temperature sensor likely failed. Simple DIY fix—unplug, remove 2 screws, replace sensor.
Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more
Replace your cracked, warped, or missing oven rack. This sturdy metal rack provides a reliable cooking surface inside your range oven cavity.
I bought an( as is) range (Maytag) form a dealer. I assumed that it would have racks, however, it came without. I tried to find some racks that would fit but none available. So I decided to order from Appliance Pros and received the right racks two days after I ordered. Very Happy Camper, Read more
Torx screw secures burner assemblies, igniters, and internal components in gas cooktops and ranges. Replace rusted, stripped, or broken screws.
I have tried to remove the burner assemblies by removing the torx screws but they were badly rusted, and unfortunately they all were broken during removal. I just discarded the ruined orifices and assembled the new orifices and burner assembly. Read more
If your oven won't heat or igniter glows but gas won't light, the igniter is likely weak. This is a common DIY repair taking 15-30 minutes.
The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more
White acrylic spray paint for appliance exterior touch-ups. Restores worn, chipped, or scratched surfaces on refrigerators, ranges, and more. 13 oz can.
Replaced It With New One Read more
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Touch up paint Read more
Replacement inner door glass panel for oven doors. Installs between outer glass and oven cavity. Needed when glass is cracked, broken, or shattered.
DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more
Seals oven door to prevent heat loss and maintain consistent temperature. Replace if frayed, flat, or allowing smoke/heat to escape. Clips install easily.
Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more
If your gas burner won't light or sparks weakly, corroded igniter screws may be the cause. These mounting screws secure the igniter to the burner assembly.
Replaced old igniter. also purchased new screws for burner and igniter assembly since old screws were corroded from spilled food/fluids etc over the years. made the installation much easier. If you need to replace a worn igniter, do yourself a favor and go to hardware store and get matching replacement screws or buy new with igniter. Now my front right burner lights every time with just a click or two. Very pleased. Read more
Replacement hinge for range oven doors. Allows door to open and close smoothly while supporting its weight. Needed when hinge is broken, bent, or worn.
Replaced the hinge and receiver. Read more
Fastens the outer panel to the interior metal door frame. Replace if stripped, missing, or damaged from wear. Required for oven door handle installation.
Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more
Adjustable leveling leg that stabilizes and balances your range. Replace if cracked, broken, bent, or threads are stripped from wear or impact damage.
The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more
Replacement mounting screw for washer drum baffles. Secures baffles to drum interior. Order if original screw is stripped, lost, or corroded during repair.
I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more