Mmv1164wb Parts

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

Watched a You tube video, showed how to remove bottom, unhook wiring, then proceed to top case. Once removed, case is turned upside down so the capture nut can be installed. Part fit perfectly and BAM, done. Case refitted and finished. Part arrived in 2 days. Great service. Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

Replaced with new grill-vent.perfect fit. Used same screws. Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

I ordered the mounting bracket, mounting hardware and template for the top cabinet. Everything I ordered was an exact fit. Install only took about 30 minutes after running the new electrical for the microwave. Appliance parts helped me save almost $400. Read more

I replaced the magnetron. Read more

I took the door off via the top torx screw pin, then pryed apart the plastic trim piece that surrounds the inner window pane with the mesh screen. I removed the inside window panel which was a little tricky, and replaced the door handle. I did it with nothing more than a flathead, Phillips, and a torx. It was very nice that AppliancePartsPros posted a link with video instructions. This easily saved me a couple hundred bucks since I didn't have to have Maytag do it. By the way,... Read more

Replaced it. The instructions did not come with the Handle and a picture I had of the parts did not tell me. I used a putty knife to removed the ring around the door and once that was off could see where the rest of the door was held in with snaps. Using the putty knife again I moved the rest of the door, to expose the handle. Unscrew the screws holding the handle placed the new one on and re-screwed it. Snapped the inter door back on and than added the frame trim back on. Putting it back... Read more

I ordered a new magnetron and a new capacitor and after they arrived I set to work. I took plenty of pictures with my phone to remind me how the components came apart but it was pretty straight forward. Once the new parts were in and everything was reassembled the microwave worked good as new. The repair was less than a third the cost of replacement and no special tools are required. Just be careful to discharge the capacitor. This website is a great resource. Read more

I looked up the problem on the Appliance Pros forum and it sounded like the magnetron needed to be replaced. We looked up and ordered the part from Appliance Pros and replaced the magnetron 2 days later when we received it. It was not a difficult replacement but was tume consuming to take it down and remove the cover to get to the part. Within about 90 minutes, we had our microwave back on duty! Read more

Bought new bracket. Took the shell off and used it to put the bracket up. Read more