Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Used to lock washer cabinet to rear wall of washer.
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first. Read more
Washer only fills with hot water or stops mid-cycle? The water temperature switch controls incoming water temps for proper cycle selection. DIY repair.
I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more
If your washer agitator won't move or clothes aren't getting clean, this agitator assembly restores wash action. Simple DIY repair in minutes.
It was fairly simple, unbolted the agitator and pulled the old one out then put in the new...although when when a load became unbalanced the rocking motion slowly strips the bolt, I would suggest if replacing this unit also order the bolt. I also bought loctite dew to the fact that the bolt was stripped. Read more
Washer motor shield deflects water, lint, and debris away from the drive motor. Replace if cracked or missing to prevent motor damage. Simple install.
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Replaced flow meter and control valve Read more
Fix a washer that won't advance through cycles or gets stuck mid-wash. This timer controls cycle sequencing. Most DIYers complete this repair in 20 minutes.
Ordered a new timer from Appliance Pros.com Read more
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. Sold individually, four are needed to replace all parts. Screw part number WP3390631.
Rubber grommet for motor mount stud.
Replaced dog ears. Read more
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more
This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it... Read more
Fixes agitator that won't move or spins slowly. This upper agitator section restores proper wash action when teeth strip or wear. 10-minute repair.
I replaced the thrust washer , agitator and agitator dog assembly. The repair took about 10 mins after watching the repair video. All works fine. Mike C Read more
10 - 16 x 1/2
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
Fix a washer agitator that won't move clothes due to stripped splines. This lower agitator base restores wash action in about 30 minutes.
Replaced the agittator Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.