Nfw 7200Tw Parts

Air chamber for water level pressure switch hose.

This motor control board regulates and powers the washer's drive motor, coordinating speed, direction, and spin. Replacing a failed module can restore proper tumbling/spinning performance and resolve common motor-related faults.

• Supplies variable-speed power to the drive motor for wash and spin
• Monitors motor feedback to maintain correct speed and direction
• Communicates with the main control to carry out cycle commands
• Common symptoms: no tumble or spin, erratic/incomplete spin, cycle stops with motor/communication errors

• Disconnect power before servicing; verify power is off
• Use ESD protection and handle the board by the edges
• Access the board inside the cabinet; move connectors one at a time and seat them fully
• Inspect the motor and wiring harness for shorts or damage before restoring power

STACK KIT FOR LONG VENT DRYER

The Shipping Bolt Kit is an OEM part for Whirlpool washing machines, specifically designed to secure the appliance during transport. This kit includes several bolts that are crucial for immobilizing the washing machine's drum, preventing any movement that could lead to internal damage while the unit is being moved. This kit includes two front and two rear shipping bolts

Causes for replacing the Shipping Bolt Kit can stem from misplacing the original bolts after installation or the bolts becoming worn or damaged after multiple uses.

Symptoms of needing a Shipping Bolt Kit include:

• Preparing a washing machine for a move without the original bolts, risking damage to the unit
• Noticing previous shipping bolts are lost or damaged, requiring replacement for future transport

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water Level Switch is an OEM part for Whirlpool washers. It is responsible for monitoring and controlling the water level during the wash cycle, ensuring the appropriate amount of water is used for each load.

A bad water level switch can occur due to electrical issues, component failure, or physical damage. If you notice problems such as incorrect water levels, overflowing, or insufficient water in your washer, it may indicate a problem with the water level switch.

Symptoms of a bad water level switch include:

• Incorrect water levels, either too high or too low
• Washer overflows or fails to fill with water
• Insufficient water for proper cleaning or rinsing

Replace your faulty water level switch with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This drum baffle mounts inside the rotating drum and lifts items so they tumble evenly through the cycle. Replace a cracked, loose, or missing baffle to reduce noise and restore consistent tumbling performance. What it does:

• Lifts and separates laundry as the drum turns for even tumbling
• Helps prevent clumping that can lead to poor results or longer cycles
• Maintains balanced drum movement; damage or looseness can cause rattling or scraping
• May help if items aren't tumbling well, you hear thumping, or garments snag inside the drum

• 1 drum baffle

• Disconnect power before servicing; for gas dryers, also shut off gas. For washers, turn off water supply.
• Open the door and rotate the drum to access the baffle's mounting screw(s).
• Remove the screw(s), disengage the baffle from its slots, and lift it out.
• Seat the new baffle in the slots and secure with the screw(s). Hand-spin the drum to confirm clearance before use.

Includes all four shipping bolts.

This cap is a small protective cover used in select appliances. It helps secure and seal its mating component, preventing leaks, debris intrusion, or loosening during normal operation.

• Maintains a secure seal/cover over the designated fitting or opening
• Helps prevent leaks and contamination in the covered area
• Can resolve issues like minor leaks, loose or missing cap, or rattling noises
• Restores proper fit and finish after the original cap is lost or damaged

• Disconnect power and shut off water or gas supply before servicing
• Note the orientation of the original cap for correct placement
• Hand-tighten only unless the OEM specifies otherwise; do not overtighten
• Inspect the mating surface or threads for damage before reinstalling

This is the siphon insert for the washer dispenser's bleach and softener compartments. It restores proper siphoning so additives empty at the right time and helps reduce standing water or residue in the drawer.

• Creates the siphon action that draws bleach and fabric softener from their cups during the rinse cycle
• Promotes complete dispensing and consistent rinse performance
• Helps minimize leftover liquid and residue buildup in the dispenser
• Typical symptoms include bleach or softener remaining after the cycle, standing water in the cups, or weak/irregular dispensing

• Disconnect power and turn off water before servicing
• Remove the dispenser drawer; lift out the old siphon from the bleach/softener cup
• Clean any debris in the cup; firmly seat the new siphon, aligned per the cup markings
• Reinstall the drawer and run a rinse cycle to verify proper draw and no leaks

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

Includes 2 adhesive pads, 2 brackets, 4 screws, and installation instructions.

This front counterweight mounts to the washer's outer tub to stabilize the drum assembly during spin. Replacing a cracked or loose weight helps curb excessive vibration, banging, and walking, restoring smoother, quieter operation.

• Adds mass at the front of the outer tub to help balance loads during spin
• Controls vibration and noise; reduces walking and off-balance interruptions
• Typical failure signs: cracked or broken weight, missing chunks, loose/rattling mount, loud knocking, severe shaking
• Visible damage to the weight or mounting area can indicate replacement is needed

• Unplug the washer and turn off water supply; wear gloves. The weight is heavy—use a second person if needed
• Support the tub and access the front of the outer tub; remove the original weight carefully to avoid damage
• Transfer and reuse any mounting hardware from the original part if needed; seat the new weight flush and tighten bolts evenly
• Run an empty test spin; inspect shocks/suspension and leveling

The Temperature Sensor is an OEM part for Whirlpool washing machines. Situated within the washer tub, the temperature sensor works closely with the control module to monitor water temperatures during all cycles. It provides vital temperature readings that allow the washer to heat water properly according to cycle settings.

Causes can be normal wear over time, impact damage or cracks in the fragile sensor head. Without this crucial component providing accurate temperature feedback, the washer lacks temperature regulation ability.

Symptoms of a failed temperature sensor include:

• Inability to heat water or inconsistent heating
• Error codes or failure to advance cycles
• Functioning only on cold water cycles
• Fluctuating or inaccurate temperature readings

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose