Rf268acrs/Xaa01 Parts

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more

I replaced the control board and the microswitch. Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

Ordered tank and heater, installed, so far so good. Thanks for the speedy order Roman Read more

Ordered tank and heater, installed, so far so good. Thanks for the speedy order Roman Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

Completely defrosted the refrigerator ,took 2days then replaced temp sensor and heater the repair took about 45 minutes so far everything is working fine Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

Removed broken piece, installed new piece. Read more

• Leaking
• Ice maker not making ice
• Not dispensing water

Put the right Samsung filter in the fridge. Read more

I called ApplianceParts Pros and 'chatted' with Robin, described the cover and reed sensor and she found the parts for me. The parts were promptly shipped and arrived when promised. The parts were what I needed and twenty minutes later the refrigerator was fully operational! Thanks ApplianceParts Pro for a great shopping experience. Read more

Spring broke on the flap of french door. Bought the spring and pin plus the cap case which I did not need. 10 minute fix and door works fine again. Super fast shipping and easy repair. Read more

Removed refrigerator panel, disconnected light and fan power. Removed fan assembly and replaced motor, grommets and fan attachment spring. Unit had adhesive on spring to help hold the spring. Chatted with customer service and clarified that spring and fan would easily pull off motor shaft. Adhesive probably was extra measure used during original build of the fridge. Noise was due to fan rubbing on housing. New fan position set to avoid any rubbing. Read more

Removed refrigerator panel, disconnected light and fan power. Removed fan assembly and replaced motor, grommets and fan attachment spring. Unit had adhesive on spring to help hold the spring. Chatted with customer service and clarified that spring and fan would easily pull off motor shaft. Adhesive probably was extra measure used during original build of the fridge. Noise was due to fan rubbing on housing. New fan position set to avoid any rubbing. Read more