Rmc275pd02 Parts

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I began by turning off the breaker. I then removed the screws securing the bake element. I immediately noticed only one side was wired and the other side was burned off. The wire for the burned off section had fallen through the hole in the back of the oven. I tried fishing it out to no avail. I removed two side trim screws, the side trim pieces, and two screws holding the built-in oven into the wall. I was able to slide the oven out and onto a square stool that was the correct height. I... Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more

Removed the Microwave from the wall, then had to almost completely disassemble the sheet metal surrounding the microwave unit itself. Lots of screws and wires to work around. Takes 2 people to remove the microwave and set it on a stand outside of the wall unit. Once you get to the light bulb, the replacement is easy, just very challenging to get to the light bulb. Read more

This was a very easy replacement of the broken glass turntable. What stood out most for me on this was the great experience I had with ApplicancePartsPros.com. I rarely, if ever, write reviews but this experience deserves notice. I found a couple other sites that had a slightly lower price, but AppliancePartsPros.com made it easier for me to verify that I was ordering the right part. On checkout, I selected standard shipping but the part arrived the next day. It was very well packaged (glass... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Touch up paint Read more

Replaced It With New One Read more

I'm a 56 year old divorced woman. I started doing these kinds of repairs to save some money and honestly, to see if I could. So yes, if I can do it, it's not that tough to do. My microwave is built in above the stove - getting it down and back up was the hardest part of the job. An extra pair of strong hands really helps-for anybody, not just a 56 year old woman. The actual repair was pretty easy. Most likely problem was pretty obvious after a little research. Easy to take off cover, get... Read more

• Little to no heat when broiling
• Element will not heat

Replaced it. Read more

We ordered the part and one extra screw(which we didn't end up using). If possible take door off your oven for easy access and have lighting source to see well. Taking part out was easy. Putting back in was more difficult because you have to match up two layers of parts in our oven. The broiler coil and the broiler shield above it. We used small craft clothes pins to keep wires from going behind the built in oven. We used a small diameter screw driver to match up holes before putting... Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

• No heat

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

We replaced the middle glass and spring by taking the door apart with no problems. Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

Replaced Magnetron and diode. Fixed problem and microwave workso again. Very time consuming because of microwave/oven built-in combo. Not easy to get to parts that needed to be replaced. Still cheaper to repair than to replace. Read more