Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces worn or leaking shock absorbers that cause excessive vibration and wobbling during spin cycles. Restores stability and smooth operation.
My washing machine was making a loud thumping sound and bouncing around a bit. Research suggested that it could be bearings and/or the spider shaft assembly. After watching the instruction videos to replace the spider or bearings, I seen you need to replace both the shaft seal and tub gasket to get to the spider and bearings. So I ordered both and waited for them to arrive. Plan was to disassemble the washer, determine what was needed, order the additional parts needed, and reassemble after the... Read more
Fixes loud banging during spin cycle and excessive vibration. Secures the drum spider assembly. Time-consuming repair (6 hours) but saves replacement costs.
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more
Creates watertight seal between washer drum halves. Replace if leaking during wash or spin cycles. Verify compatibility with your model number.
Washer won't start or shows door error? This door lock switch assembly fixes door latch issues. DIY-friendly repair with video guide, typically done in 15 minutes.
Replaced door lock switch. Read more
Secures the door boot gasket on your washer. Replace if seal pops off, leaks occur, or spring wire breaks. Confirm fit with your model number.
Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more
Fix a washer that won't drain or stops with a humming sound. This drain pump removes water during wash cycles. DIY repair takes about 10-30 minutes.
Replaced drain pump. Your video on your web site was very helpful. Read more
Prevents water leaks between washer tub and drum. Replace if you notice leaking, grinding noise, or water damage. Confirm fit with your model number.
Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more
Washer not filling with water or showing 4E error? The water inlet valve controls flow into your machine. DIY repair in 15-40 minutes with video guide.
I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more
Washer won't drain or draining slowly? A failed drain pump prevents water removal during cycles. Moderate DIY repair with video guide available.
I opened the washer and replaced the pump. To open the washer: 1. Remove the 2 screws that are different from the others in the top back corners of the machine. That will let you remove the top. 2. Remove the soap tray and its holder. The tray comes out if you depress the tab in the back center. Its holder comes out if you remove the two screws in the front. You can leave all the hoses attached. 3. Remove the control panel. It snaps in. Undo the top snaps first. You'll have to reach... Read more
Replace your broken, cracked, or missing dryer control knob encoder assembly. Mounts to the front control panel for precise cycle selection control.
Ordered new control knob and replaced broken one. The most difficult part was popping out the control panel so I could access the control knob. I ended up "wrestling" it out. It would be wonderful if the product manual had some guidance on how to pop out all panels. Read more
Fixes loud banging noise during spin cycle caused by cracked or broken balancer. Concrete weight stabilizes drum movement. Moderate DIY repair.
Replaced parts. Read more
Fix a washer door that won't close or lock with this door latch assembly. Typical repair for broken latches takes about 15 minutes. Easy DIY install.
I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more
Fix 3E error codes or spinning issues with a rotor position sensor replacement. Detects motor position for smooth wash cycles. 15-minute DIY repair.
I watched the you tube video that completely explained how to do it. It was very easy to do. Read more
Washer Assembly Bolt is essential for securing components in your Samsung washer. Crafted as a genuine OEM part, it ensures durability and reliability in your appliance. This bolt assembly is specifically designed for Samsung washers, guaranteeing a perfect fit and easy installation. Made from high-quality materials, it withstands the demands of regular use, providing long-lasting performance. Replacing worn or damaged bolts with this genuine OEM washer assembly bolt helps maintain the structural integrity of your machine, ensuring it operates smoothly and efficiently. By choosing this reliable part, you can confidently restore your washer to optimal working condition, enhancing its lifespan and performance. Trust in this Washer Assembly Bolt to deliver the functionality you need for a dependable laundry experience.
I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more
The Dryer Knob Encoder Assembly is an essential component for Samsung dryers, ensuring precise control of your appliance's settings. This genuine OEM part guarantees a perfect fit and reliable performance, allowing you to easily adjust drying cycles and temperatures with confidence. Crafted for durability, the Dryer Knob Encoder Assembly enhances the functionality of your dryer by accurately translating knob movements into electronic signals, resulting in consistent and efficient drying results. Installation is straightforward, making it a convenient solution for restoring your dryer's performance without the need for professional assistance. Whether your original encoder is worn out, unresponsive, or damaged, this Dryer Knob Encoder Assembly provides a seamless replacement that maintains the quality and efficiency of your Samsung dryer. Improve your drying experience with this dependable part, designed to keep your appliance running smoothly and extend its lifespan.
Ordered a new knob and took out little bits of the old one. Took the new knob and pressed it over the stump and presto works like new. Read more
Secures the inner door boot seal on front-load washers. Replace if seal is loose, leaking, or damaged. Confirm fit with your model number before ordering.