Whirlpool Rc8700edb-2 Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 715878
This 8 inch drip pan installs under coil burners to catch spills and protect your cooktop. Replace cracked, rusted, or heavily stained pans to restore appearance.
Do-It-Yourself Stories from Customers like You
One contact spad was corroded and looked burned both coils failed to come on Charles M. • Fairburn , GA • October 26, 2014
$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils.
Read more
More
$11.78
- Compare At:
-
$17.50
- You Save:
-
$5.72
Genuine Whirlpool part
By: Whirlpool
Part Number: W10823711
Burner not heating or 'Hot Surface' light stays on? This electric cooktop surface element is likely the fix. DIY-friendly, most installs take 15 minutes.
This part fixes the following symptoms
-
Element will not heat
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Burned out element on ceramic top range Charles P. • Marietta , OH • September 13, 2014
Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same...
Read more
More
$142.41
- Compare At:
-
$169.47
- You Save:
-
$27.06
Genuine Whirlpool part
By: Whirlpool
Part Number: 715877
Replacement 6-inch drip pan for electric ranges and cooktops. Installs under burner element to catch spills and debris. Replace if cracked or warped.
This part fixes the following symptoms
-
Touchpad does not respond
See more...
Do-It-Yourself Stories from Customers like You
One contact spad was corroded and looked burned both coils failed to come on Charles M. • Fairburn , GA • October 26, 2014
$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils.
Read more
More
$10.71
- Compare At:
-
$15.44
- You Save:
-
$4.73
Genuine Whirlpool part
By: Whirlpool
Part Number: 12001676
This electrical connection kit provides secure terminals where your range's surface heating elements plug into the cooktop. It ensures proper electrical contact and power delivery to the burners. Replace when burner elements don't heat properly, connections appear burned, or elements won't stay securely in place.
This part fixes the following symptoms
-
Element will not heat
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
No power to both burners in removable tray of c203 unit Eric O. • Southbury , CT • April 07, 2017
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly.
Unfasten spade insulation block (located in the front of the tray) after...
Read more
More
$19.31
- Compare At:
-
$22.98
- You Save:
-
$3.67
Genuine Whirlpool part
By: Whirlpool
Part Number: W11120791
Burner stuck on high or won't turn off? This burner control switch regulates heat settings. Moderate DIY repair—label wires before swapping.
Do-It-Yourself Stories from Customers like You
Burner only worked on high Thom R. • Bowdoin , ME • February 12, 2016
If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well.
Read more
More
$78.27
- Compare At:
-
$93.92
- You Save:
-
$15.65
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY706012
Grease filter for range hoods and over-the-range microwaves. Dimensions: 9" x 16-1/2" x 3/32" (9 x 16.5 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
Do-It-Yourself Stories from Customers like You
Burner in glass top range control only has off or full on modes Edward A. • Brookfield , WI • August 11, 2015
Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good.
Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As...
Read more
More
$50.57
- Compare At:
-
$60.18
- You Save:
-
$9.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY04100166
If your cooktop burner won't heat or heats unevenly, the surface element may be faulty. Simple plug-in replacement takes under 10 minutes to install.
Do-It-Yourself Stories from Customers like You
The coils and drip pans were really worn out coils were falling apart and the pans were chipped and stained Janice J. • Terrell , TX • August 14, 2015
Installed the new pans and replaced the coils. My Jennaire looks like new. Only took minutes and made such a difference.
Read more
More
$41.95
- Compare At:
-
$49.92
- You Save:
-
$7.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY04100165
Burner not heating or working on your range? This surface heating element restores cooking performance. Simple plug-in replacement in under 10 minutes.
Do-It-Yourself Stories from Customers like You
The burners on my drop in stove would not work the connections and the surface elements were in bad shape Luise C. • Worth , MO • November 23, 2014
I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help.
Read more
More
$52.68
- Compare At:
-
$62.16
- You Save:
-
$9.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4159193
Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.
Do-It-Yourself Stories from Customers like You
Hinges were weak Don M. • Colchester , VT • December 31, 2016
Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair.
Read more
More
$8.56
- Compare At:
-
$10.27
- You Save:
-
$1.71
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY708730
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
- Creates a fixed, insulated junction between external supply wires and internal appliance wiring
- Maintains tight screw-lug connections to minimize resistance and heat buildup
- Helps ensure steady power delivery to controls, motors, and heaters
- Common indicators of failure: melted/discolored block, burning odor, visible arcing, loose or stripped terminals, intermittent or no power
What's included: 1 terminal block Install notes:
- Disconnect power at the breaker and verify zero voltage before servicing
- Photograph/label wire positions; transfer one lead at a time to the new block
- Tighten terminal screws firmly; do not overtighten into the insulator
- Inspect wire ends/ring terminals and strain relief; replace any heat-damaged components per the service information
Do-It-Yourself Stories from Customers like You
Old and rusting Edwin H. • Corpus Christi , TX • December 14, 2016
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat.
Read more
More
$53.21
- Compare At:
-
$63.32
- You Save:
-
$10.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY702434
This ceramic receptacle provides the electrical connection point for a plug-in heating element on a range or cooktop. It mounts inside the cooktop surface and receives the element's terminal prongs to deliver power. Replace this part if the element fails to heat, heats intermittently, or if the receptacle shows signs of burning, arcing, or melting.
Do-It-Yourself Stories from Customers like You
Burned contact spade Charles M. • Fairburn , GA • May 26, 2016
Took apart the burner unit and replaced burned spade. Did not need the receptacle, so returned it, but did have to order the contact and lead wire that burned out in it, and what really caused the whole problem. That will be covered in another repair note for that part.
Read more
More
$54.25
- Compare At:
-
$64.56
- You Save:
-
$10.31
Genuine Whirlpool part
By: Whirlpool
Part Number: W10823693
Burner not heating? This surface heating element restores reliable heat to your cooktop. DIYers report straightforward installation in under an hour.
Do-It-Yourself Stories from Customers like You
One surface element and part of the top glass are broken Jason S. • Cupertino , CA • November 18, 2014
First, I just unscrewed all nuts that are holding the frame and all surface elements. Once all parts, surface elements, control switches, are loose from the original glass, I just moved all parts to the new glass. Due to the weight of the glass, all actions have to be done carefully as I broken one corner of the glass couple of years ago when I replaced one of the control switch.
Read more
More
$139.47
- Compare At:
-
$167.36
- You Save:
-
$27.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP71002187
Replace a cracked, broken, or missing burner control knob on your cooktop. This knob installs on the control panel to adjust burner heat settings.
More
$27.37
- Compare At:
-
$32.57
- You Save:
-
$5.20
Genuine Whirlpool part
By: Whirlpool
Part Number: Y708572
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
- Creates a reliable electrical connection between a wire lead and a flat spade terminal on a component
- Helps prevent arcing, heat build-up, and intermittent power caused by loose or burned terminals
- Common symptoms include: component won't power or heat, intermittent operation, visible discoloration or melting at the connector
- Direct replacement for a damaged or fatigued push-on terminal
What's included: Contact spade only Install notes:
- Disconnect power to the appliance before servicing
- Match the size/orientation to the original terminal and replace any discolored or heat-damaged wiring/insulation
- Use an appropriate crimp tool to attach the terminal to the wire lead; ensure a firm crimp
- Push fully onto the mating blade for a tight, secure connection
Do-It-Yourself Stories from Customers like You
No power to both burners in removable tray of c203 unit Eric O. • Southbury , CT • April 07, 2017
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly.
Unfasten spade insulation block (located in the front of the tray) after...
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY707985
This is a blower wheel used in the downdraft exhaust ventilation system of a range or cooktop. It mounts on the motor shaft and draws smoke, steam, and cooking odors down and out through the vent ductwork. Replace this part if the exhaust fan is noisy, vibrating excessively, or not moving air effectively despite the motor running.
Do-It-Yourself Stories from Customers like You
Stove downdraft stopped working Robert B. • Gaithersburg , MD • March 08, 2016
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business.
Read more
More
$94.67
- Compare At:
-
$112.66
- You Save:
-
$17.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP5700M426-60
This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.
Do-It-Yourself Stories from Customers like You
Parts needed replacement Maria C. • Spring Hill , FL • September 07, 2015
Ordered all the parts needed, replaced them and the Jenn Air worked just fine.
Read more
More
$179.37
- Compare At:
-
$213.45
- You Save:
-
$34.08