Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Float Assembly is an OEM part for LG washing machines. This part monitors and controls the water level within the appliance. It's a safety feature that prevents water overflow and potential flooding, contributing to the efficient operation of the washing machine by maintaining the correct water level for each cycle.
Causes of a bad Float Assembly can vary from simple blockages that prevent the float from moving freely to electrical faults within the switch mechanism.
Symptoms of a bad Float Assembly include:
This OEM LG part is also compatible with some Kenmore models.
The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more
The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.
Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.
Symptoms of a bad vent hose include:
This OEM LG part is also compatible with Sears/Kenmore.
Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more
Filters debris from water entering your washer. Replace when water flow is reduced or sediment buildup occurs. Verify fit with your model before ordering.
I was cleaning the supply hose filter screen constancely, I had no Idea there was filter screens in the pump intakes on the machine. once I found them and replaced them, I had plenty of water, so don't buy supply hoses with the screens in them until you check to see if your machine has them already. Read more
The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.
Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.
Symptoms of a bad clamp include:
This OEM LG part is also compatible with Sears/Kenmore models.
If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more
Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.
Watched a whole bunch of YouTube videos to replace the tub bearings. Completely disassembled the washing machine. Found that water leaked past the rear tub gasket causing the inner tube bearing to corrode. Replaced both bearings and tub gasket. Inner bearing was the cause of the problem but I replaced both bearings and tub gasket. Read more
Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.
Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more
Directs water from inlet valve to detergent dispenser in LG washers. Replace if hose is cracked, leaking, won't stay attached, or damaged from wear.
I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more
Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.
Took top off and did a line at a time Read more
Washer won't spin or shows LE error? A faulty motor wire harness disrupts power to the drum motor. DIY fix in 20-60 minutes with basic hand tools.
I replaced the rotor and stator motor assembly. Read more
Bleach dispenser funnel for LG front load washers. Installs in detergent drawer to safely dispense bleach. Replace if cracked, broken, or missing.
The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more
This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.
Replacement bolt that secures the spider assembly to the inner wash basket. Needed when hardware is missing, stripped, or corroded during repairs.
Can't buy LG parts in Canada without getting an LG Tech to install. $1000 repair was too steep for me so went on websites and bought from Appliance Parts. Watch the video on Appliance Parts. Note - Joyce from Appliance Parts really helped in identifying the bolts that I needed. Read on and you will see why. Stripped down machine and identified the spider had failed along its three arms. Bearings were still in good condition. Managed to get three bolts off spider but remaining three had same... Read more
Fix a washer door that won't close or latch properly. This locker hook engages the lock mechanism to secure the door during cycles and prevent error codes.
Includes sensor probe
This noise filter assembly is an electronic component that suppresses electromagnetic interference (EMI) generated by the washing machine's motor and control circuits. It helps prevent electrical noise from feeding back into your household wiring. Replace this part if your washer fails to start, shuts off unexpectedly, or causes interference with nearby electronics.
Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more
Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.
I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.