Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Plastic trim bezel that mounts around the lid lock on your top-load washer's panel. Replace if cracked, broken, or missing to restore a clean finish.
Put in new lid lock. This is my second one in 1 year. Whirlpool suggested I leave it loose so that if somebody did try and force it open, it wouldn't break it. This lid lock has 4 wires and cannot be bypassed. Read more
Secures the washer lid to the hinge assembly. Replace if stripped, rusted, or missing. Essential for proper lid alignment and secure closure during use.
I just replaced the glass lid and broken plastic frame with the all metal one. Call 877 477 7278 for appliancepartspros and order the following Whirlpool parts (prices as of November 2016): 1 lid part number WP8572026 (AP6013408) for $119.81 2 hinges WP8563964 (AP6004844) for $6.17 each 4 screws WPW10119828 (AP6015313) for $1.97 each Total $140.03 plus $8.95 shipping, grand total $148.98 Note that it does not say that this lid will fit model 7800, but the lid will fit this model. The... Read more
Washer overfilling or not filling properly? A damaged pressure switch hose prevents accurate water level sensing. Easy 15-minute DIY fix with video.
I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more
Replace a cracked, leaking, or worn balance ring on your washer. Attaches to the spin basket to stabilize the drum and reduce vibration during spin cycles.
I first checked to make sure the washer was level. The washer is on a concrete floor. After watching lots of you tube videos I ordered all the parts that could be causing this problem. I ordered: Balance Ring, Suspension Pad Kit (3 rectangle plastic wear pads), Tub Suspension Pads(3 curved plastic wear pads), Suspension Spring, and a Spanner Wrench tool. After getting the washer apart it was obvious that the problem was the Tub Suspension Pads they had completely worn away so that only the... Read more
Secures the control console to the top panel of your dryer. Replace this clip if it's broken, cracked, or missing to keep the console firmly mounted.
Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Fix a washer that hums but won't spin or agitate with this motor start capacitor. Repairs motor startup issues. Moderate DIY, 30-60 minutes.
Found the motor switch was fried. So replaced that and the capacitor. Starts fine now. Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Replaces cracked, worn, or missing washer lid bumpers. Cushions lid closure and reduces vibration. Sold individually. Installation video available.
Found AppliancePartsPros on-line. Sent us the manual, parts list, etc. via .pdf files. Our local guy did not. Had parts in stock, two day shipping, totally painless. The parts were approximately 1/2 the price the local guy wanted. OEM parts. Perfect fit on replacement. The Whirlpool is so well made, it was very easy to repair. It has several items, over the years, which failed. In all cases, repair was painless with a few common hand tools and a tad of patience. AppliancePartsPros had... Read more
Fix washer rattling noise or loose cabinet with this retaining clip. Secures cabinet to back panel. Easy snap-in installation takes 10 minutes or less.
After looking at several YouTube videos, we decided we could attempt to fix this ourselves. We found the easiest video to follow from Appliance Parts, and ordered the clips and lid switch assembly (the clips we had to replace because we goofed that one ourselves). The parts came within a couple of days. The repair took a little over 1/2 hour only because we had to re-do some steps because my husband was over anxious and did some things without reviewing the video. Overall, it was a very... Read more
Loud rattling or loose agitator during wash? This clip secures the agitator assembly to eliminate noise and restore proper back-and-forth motion. Quick DIY fix.
Found that by manually spinning agitator one direction it seemed free, but spinning counterclockwise it seemed to stick a little. Pulled dispenser and agitator and found the agitator washer hole was oval rather than round. Replaced the agitator washer and the washer seems to sound normally for now. Not sure if the new agitator washer will eventually grind down due to non-circular action from the transmission, or if the agitator and clip will keep the transmission centered long term. Should... Read more
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
I put all pieces that I ordered on the dryer and plugged it in. Read more
If your washer agitator spins freely or won't move clothes, the upper agitator may be worn. Often replaced with agitator dogs. Video guide available.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
Spacer that maintains proper alignment between the washer cabinet and top panel. Replace if broken, cracked, or missing to restore stability.
Replacement timer knob for washers. Installs on the control panel to adjust wash cycle settings. Replace if cracked, broken, or won't stay attached.
I watched your video on the installation and after 3 views it was done thanks it making it easy. Read more
Rubber inlet hose that connects your washer to the water supply. Replace if cracked, leaking, or worn. Standard 5-foot length with included washers.
Replaced flow meter and control valve Read more