Yard Machine Spring Tromm Spark Arrestor Parts

The Cover, Lamp is an OEM part for LG dryers. This component covers and protects the interior lamp inside the dryer, ensuring it stays secure and free from damage while providing illumination inside the drum.

Over time, the lamp cover can become cracked or damaged due to the high temperatures and vibrations within the dryer. It is essential to replace a faulty lamp cover to maintain the proper lighting and protection for the lamp.

Symptoms of a bad lamp cover include:

• The interior lamp not staying in place
• Visible cracks or damage on the cover
• Reduced or blocked light inside the dryer drum
• The cover falling off or becoming loose

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

The Spider is an OEM part for LG washing machines. As the rear tub support, it is located behind the outer tub and provides structural support during the spinning cycles. The spider braces against excessive vibration and movement to maintain integrity of the washer tub under heavy loads.

Causes of a bad spider can include cracks, breaks, or loosening due to wear and tear over time from stress of the spinning cycles. Metal fatigue from years of use also contributes.

Symptoms of a bad spider include:

• Excessive shaking and rattling during spin cycles
• Rubbing or grinding noises emanating from the rear of the washer
• Difficulty with load distribution and spinning effectiveness
• Potential leaks due to compromised tub support

This LG part is also compatible with some Kenmore models.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

This Power Cord Assembly restores a secure, grounded connection from your wall outlet to the washer's internal power circuit. Replace a frayed or failed cord to resolve no-power issues and maintain safe operation. What it does:

• Delivers AC power from the wall outlet to the washer's internal power circuit (line filter/control)
• Provides a proper equipment ground path for the cabinet
• Replaces damaged or overheated cords that can cause power loss
• Common symptoms include: washer has no power, won't start, intermittent power when the cord is moved, or visible cord/plug damage

• 1 power cord assembly

• Disconnect the washer from power before servicing and verify the outlet/breaker are in good condition
• Access cord connections by removing the rear or top panel per your model's service information
• Note original routing and strain relief; reinstall clips/guides the same way to prevent chafing
• Secure the ground connection and fully seat all terminals; keep wiring clear of sharp edges before testing

The Drawer Front Panel Assembly is the complete replacement front for a pull-out drawer. It restores a clean look and solid handle support so the drawer opens and closes smoothly and sits flush again. What it does:

• Attaches to the drawer frame to provide the finished outer front
• Supports handle mounting and helps keep the drawer aligned
• Common fix for a cracked or dented front, broken mounting tabs, or a loose/missing panel
• Can help resolve a drawer that won't close flush or feels wobbly

• 1 drawer front panel assembly

• Disconnect power before servicing; remove items from the drawer to reduce weight
• Remove the handle and mounting screws; support the panel as you lift it off the drawer
• Transfer any reusable hardware from the old panel; align the new panel and tighten fasteners evenly
• Test drawer operation and fit; adjust as needed per service information

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.

This safety cover is an internal protective shield used inside the dryer to guard components and help maintain proper airflow. Replacing a cracked or missing cover helps keep wiring and moving parts enclosed for safer operation. What it does:

• Shields internal wiring and components from accidental contact
• Helps channel air and lint flow as designed
• Replaces a damaged, heat-warped, or missing cover
• Helps resolve rattling/vibration noises and visible gaps where the cover mounts

• Includes 1 safety cover

• Unplug the dryer; for gas models, shut off gas and allow the unit to cool
• Access the cover location per your model's service manual; remove panels as needed
• Position the cover correctly and secure using existing hardware/clips
• Do not operate the dryer with the cover removed or loose

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

This inlet hose supplies fresh water from the household line to the dishwasher. Replace a damaged or leaking hose to help restore proper filling and prevent water leaks during operation.

• Channels water from the supply valve to the dishwasher's inlet
• Common failure signs: leaks under or behind the unit, fill errors, slow or no fill
• Helps resolve intermittent water supply issues caused by a kinked or cracked hose

• Unplug power and shut off the water supply before starting
• Place a towel or pan to catch residual water when disconnecting
• Check for leaks after installation and tighten connections as needed

This hose connector joins two internal water lines inside your washer to create a secure, leak-resistant connection. Replacing a worn coupler helps stop drips and keeps water moving properly during fill, wash/recirculation, and drain cycles.

• Joins two hoses inside the appliance for a tight, reliable seal
• Helps maintain proper water flow during operation
• Replace if cracked, deformed, or if hoses slip off despite clamp tension

• Unplug the washer and turn off water supply; expect some residual water
• Access the hose junction and note hose routing and clamp positions
• Fully seat hoses onto the connector and secure clamps behind the hose bead
• Reassemble and run a short test cycle while checking for leaks

This nozzle connector links a water hose to the washer's nozzle/dispenser assembly, creating a tight, leak-resistant connection. Replacing a worn connector helps stop leaks and restores consistent water flow during fill and spray functions. What it does:

• Couples the hose to the nozzle/dispenser assembly and maintains a watertight seal
• Directs water into the dispenser or tub as designed
• Typical failure symptoms: leaks near the top panel or dispenser, loose hose, weak or erratic spray/fill
• Cracking, hardening, or deformation can lead to drips and connection issues

• 1 nozzle connector

• Disconnect power and shut off water supplies before servicing
• Remove the top cover to access the dispenser/nozzle area; protect the work area with a towel
• Release hose clamps, seat the hose fully on the new connector, and secure clamps firmly
• Run a brief fill/rinse to check for leaks before reassembly