Power Strike Small Engine Spark Plug Parts

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

• Won't start

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

• Door latch failure

Disconnect existing part and connect new one. Disconnect involved removing back cover around lock and electrical connector. Also had to remove rubber gasket. Read more

Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes. Read more

• Door won't close

I just simply just take 2screws off and remove old latch off and replace new latch on. This is easy not that hard. Read more

Watched you tube video, fixed with no problem. Read more

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

• Will not agitate
• Will not drain
• Won't start
• Timer will not advance

Ordered new lid switch and plunger. Watched help videos and installed new parts, Washer works like new. Read more

Tried bending the strike to get a firmer grip, but no luck. Replaced the door latch and strike. Washer is about ten years old. You can feel the new catch has a more positive engagement. When you replace the strike, be sure not to tilt it downward in front. It will go in the way but it will keep the door from closing. Not sure I needed to replace the strike but didn't want to risk more downtime. Read more

Replaced lint filter and door latch, but door switch was the answer. Works great! No video for this model but was able to view a similar one to follow. Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more

• Door latch failure
• Will not agitate

After watching the video it was strait forward. Just Pull the screws pop the lid swap the springs "grease them" and put it back together. I would suggest that you have a person help you mostly has a second pair of hands. The lid was over rear springs and it will save you some expletives to have the extra body. I had worn out springs and the load kept becoming unbalanced during spin cycles I just happened to coincide with the Lock mechanism failing. The motor drive for the lock stopped working.... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow. Some professionals say that if one of these sensors fail, both... Read more