Power Small Engine Start Switch Parts

I purchased a new heating element. Very easy to fix in about twenty minutes Read more

Bought a new switch assembly, watched the video, and replaced the switch. Thr dryer now runs fine. Replacement part matched esxactly. Read more

• Element will not heat

We cut the power, took the control panel off, got the burner switch number from the original part, and ordered a new one. We were a little worried at that point, because your website offered a "replacement" part, with a different number than the original. However, we put the model number into your double check feature and were assured that we were getting the right part. The part arrived in two days and frankly we were still worried, because the new part was slightly larger than the original.... Read more

When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to... Read more

• Won't start
• Element will not heat

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more

I had to take the control board off the bottom of the cooktop and replace the fan switch. The post that fits into the hand switch had broken off. The new switch cost about $35, it was an exact replacement and the whole repair took less than an hour. My wife is very happy because now she can again use the downdraft fan on the cooktop. Thank you AppliancePartsPros. Read more

Replaced the large burner control switches for the ones giving trouble. Since the other two switches had seen as much use as the faulty ones, replaced them too. After putting in new switches, found that one large burner had burned out so replaced it also. Range now cooks as good as new Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Will not fill with water

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more

I ordered the infinite switch control from Appliance Parts Pro on a Wednesday afternoon and it arrived well packaged the next day even though I selected standard shipping. Thank you for the easy ordering and fast delivery! Replacing the old switch was easy: 1. Disconnect the power to the stove 2. Make sure the power is off to the stove 3. Pull 4 burner control knobs off and remove 4 large nuts attached to the 4 burner switches 4. Lift the face plate off and clean previously hidden cooking... Read more

If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more

• Will not fill with water
• Will not agitate

First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more

My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more

The problem seemed to be with the switch so I watched a few youtube videos to learn more about how ranges work. After locating the correct replacement switch I ordered it on-line around 10 pm Tuesday night. The new switch arrived Thursday morning at about 10 am and I had my range back up and working like new in less that 30 minutes. The hardest part was figuring out how to remove the slide in panel to access the switch. There were plastic washer/nuts behind each know which I was able to... Read more