Thermal Fuse Parts

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

• Monitors water clarity/soil level during the wash
• Sends feedback to the control to adjust cycle length, rinses, and heating
• Failure can cause very long or very short cycles
• Can trigger sensor-related fault indications

• Disconnect power at the breaker and shut off water before servicing
• Access the sensor from the bottom near the sump; remove the toe panel if needed
• Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
• Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

Washer not heating water or showing tE error? This temperature sensor monitors water temp and signals the control board. Moderate DIY repair fixes temp issues.

If your dryer takes too long to dry or overheats, the cycling thermostat may have failed. This part regulates heat by cycling on and off. Easy DIY fix.

This sensor monitors water flow inside the dishwasher to ensure proper water circulation during wash and rinse cycles. It sends signals to the control board to regulate water intake and pump operation. Replace this sensor if the dishwasher displays error codes related to water flow, fails to fill properly, or stops mid-cycle due to incorrect flow detection.

Microwave has no power or won't start? A faulty cavity thermostat often causes complete shutdowns. This part restores temperature control in 5-10 minutes.

Dryer not heating or running too hot? This high-limit thermostat regulates temperature to prevent overheating. Easy DIY fix takes 30 minutes or less.

This sensor monitors operating conditions and relays accurate feedback to the control so cycles run properly. Replacing a failed sensor helps restore correct operation and prevent erratic behavior or fault codes. What it does:

• Detects a specific operating condition and sends a signal to the control
• Helps the machine regulate cycle timing and performance
• Can cause error codes, cycles that won't start or advance, or intermittent shutdowns when failing
• Lead to inconsistent temperatures or sensing behavior depending on application

• 1 sensor

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Access the sensor; note wire positions and connector orientation
• Install the new sensor in the same location and orientation; seat connectors fully
• Clear any stored faults and run a test cycle per the tech sheet

Fixes long dry times and temperature issues. This dryer thermostat regulates heat cycling to prevent overheating or underheating. Simple repair.

Dryer won't start or overheats? A faulty high-limit thermostat breaks the heating circuit to prevent damage. Easy 5-10 minute DIY replacement fix.

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle

Ice maker not producing ice or overflowing? Failed thermistor prevents proper temperature monitoring. Direct plug-in replacement restores ice production.

Fix soap not dispensing or rinse aid leaks with this washer detergent dispenser assembly. Restores proper detergent release during wash cycles.

Dryer won't heat or start? A failed thermostat breaks the heating circuit. Common DIY fix—test for continuity with a multimeter. Typical repair time: 30-60 minutes.

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

• Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
• Provides the bias function used by automatic cycles for correct temperature control
• Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
• Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

• Disconnect power before servicing; for gas models, also shut off the gas supply
• Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
• Ensure the thermostat mounts flush for proper sensing; tighten screws securely
• After replacement, verify good airflow and clear venting to prevent repeat failures

Microwave won't turn on or has no power? A blown fuse is often the cause. This safety fuse protects circuits from shorts. Requires cover removal to replace.

The Dryer Guide Sensor Assembly is designed to ensure precise drying cycles in your Samsung dryer. This genuine OEM part guarantees compatibility and reliable performance, maintaining your dryer's efficiency. Featuring a high-quality assembly, it accurately monitors moisture levels, helping to prevent over-drying and reduce energy consumption. Installing the Dryer Guide Sensor Assembly enhances the lifespan of your appliance by ensuring optimal operation. Whether you're replacing a worn-out sensor or repairing your dryer, this component provides a seamless fit and easy installation. Trust in the Dryer Guide Sensor Assembly to deliver consistent drying results, improving your overall laundry experience. Compatible with a range of Samsung dryer models, this genuine OEM part is the perfect solution for maintaining your appliance's functionality and performance.