Bake Element Terminal Wiring Parts

• Light not working

I pulled out the wiring harness for the bulb and really inspected the sockets. (The wire connections on one of the sockets were really loose and the inside of that socket was a little melted.) I replaced the light wiring harness and sockets. It was a really simple fix. I turned off the power to the range hood at the breaker box first. I removed the filters and the light bulbs. I only needed a medium sized crosspoint screwdriver to remove 5 screws that hold up the light housing. The... Read more

I called GE and they sent a tech out. $89 service call. Had I REALLY inspected the oven the hidden element had blown and separated and part of it welded itself to the inside of it's compartment. GE wanted another $350 to come back and fix it. I bought the part here for around $55 and had it running again in about an hour! Read more

• Too hot
• tripping breaker

I found the assembly with heater element, thermostat, and the thermal fuse already assembled (cheaper than finding what part was bad and ordering that one part). unplugged dryer, pulled it out and removed the dryer exhaust tube, the top and front. The harness was a little short so I wasnt able to pull the whole heater assembly out before disconnecting. BEFORE disconnecting I took a picture so that if my brain forgot what wires went were!!!! put the dryer back together and put a load that just... Read more

Would advise before doing this repair to watch the video for it. It is not a plug in connection anymore like older ovens. The key is to keep the connecting wires from the oven from falling or pulling into the inner wall of the oven. The wires may not come very far out away from the wall of the oven so make sure to secure them. The video shows a good way to do that. If you have an in wall oven this is very important because it would hard and time consuming to pull the oven out of the wall to... Read more

Turned stove breaker off in the main breaker box and also unplugged the oven from the 220 outlet. pulled the baking racks out of the oven and proceeded to locate the 1/4 screws just above the bake element where it passes through the metal wall and removed them. pulled the element forward until the wires were exposed and unplugged them and then attached the new element to the wires and reinstalled in reverse order. Read more

Range has no model ID plate anywhere. Flip off electric at circuit breaker box. Opened top of range and noted details of the faulty burner, including confirm that outer coil was fried. The maker info on back of element was useless in finding replacement: more useful was general shape, and the numbers around edge on back. Close up range, since low heat element still working. Turns out all Maytag double oven Gemini ranges use the same hi-low element, but double check appearance just in... Read more

• Little to no heat when baking
• Oven not heating evenly

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Ordered part and installed it. Broiler works as advertised. Read more

Replaced the elements with new ones ordered through Appliance Parts Pros. I wanted to tell you how pleased I am that I ordered the baking and broiler elements for my Maytag oven from you. Your website diagrams for my model of oven helped immensely in figuring out what parts I needed. Your order process was easy and the parts arrived within two days just as stated. Best part of all, the new elements work perfectly! I will bookmark your site for future appliance part needs and I look forward to... Read more

Replaced: condenser fan motor, defrost timer, defrost thermostat (bi-metal), and added a heat probe. Fan motor obviously shot... hard to turn by hand. Defrosted for 48 hours, cleaned & bleached drain tube. Never tried to test the old timer or bi-metal but it now runs perfectly and tightly maintains 39/0 degrees with dry fridge. When reassembled and powered up, compressor did nothing... I advanced the timer knob until condenser started. Hung the heat probe securely on defrost element and... Read more

Replace element. Read more

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more