Hardware Hand Small Engine Start Switch Parts
Bestselling
Price High to Low
Price Low to High
By: Frigidaire
Part Number: 5304509458
This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.
Transfers motion from the door-open button to the latch hooks to release the door Helps resolve a door that won't open when the button is pressed Addresses a button that feels loose, sticks, or lacks resistance Replaces a cracked or broken lever causing intermittent door operation What's included: 1 lever Install notes:
Unplug the microwave and discharge the high-voltage capacitor before servicing Remove the grille and control panel to access the interlock/latch area Note spring and pivot orientation and transfer any reusable hardware Test door release action before completing reassembly
Do-It-Yourself Stories from Customers like You
Microwave blew line fuse Gerald G. • St. Louis , MO • August 05, 2019
It took a long time to determine the problem but eventually I discovered that the plastic bracket (latch hook) that held the three door-switches showed appreciable wear from repeated door openings and closings. This wear stopped the door from sealing properly and the door switch safety mechanism blew the line fuse. I replaced the worn bracket (AP6230612) as well as the plastic latch mechanism (AP4553585) on the door that engages this bracket (and of course the fuse too) and the microwave now...
Read more
More
By: Whirlpool
Part Number: WP3391902
Dryer won't start or keeps running with door open? A faulty door switch prevents proper start/stop control. Easy DIY fix in under 30 minutes restores safety.
Do-It-Yourself Stories from Customers like You
Stacked washer/dryer dryer light stayed on when door closed and dryer would not turn on. 25 years old Neal Jay M. • Portland , OR • June 12, 2019
Order part and removed 3 hex head screws at top front edge of dryer and slightly lifted up on control panel to lift off pane. It has hangers that support panel while servicing. Remove 2 screws at inside top edge of dryer opening (where lever of switch protrudes) disconnect 3 wire clips at old switch and restore wire clips at new switch and place switch into position and restore 2 screws to secure switch body.
Read more
More
By: Ge
Part Number: WH12X10141
Fix a washer that won't agitate or spin with this lid switch. This safety part detects if the lid is closed. Easy DIY repair with basic tools.
Do-It-Yourself Stories from Customers like You
Washing machine would agitate but not spin Kevin T. • Overland Park , KS • January 27, 2020
Replaced lid switch and capacitor
Read more
More
By: Ge
Part Number: WB01X34910
The Door Removal Tool is an OEM replacement part for GE microwave ovens. It is a specialized tool designed to assist in the safe and proper removal of the microwave door. This tool is essential for servicing, repairing, or replacing components within the microwave cavity, ensuring that the door can be securely detached and reattached without causing any damage.
Symptoms of needing the Door Removal Tool include:
Requirement to access the interior components of the microwave for repairs or maintenance
Difficulty in removing the microwave door using conventional methods
Potential risk of damaging the door or other components without the proper tool
Causes for needing the Door Removal Tool can vary, but it is typically required when performing tasks such as replacing the magnetron, waveguide cover, or other internal parts that necessitate door removal for access.
This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore microwave models.
Do-It-Yourself Stories from Customers like You
The broken upper door for GE microwave/oven combo. Charles S. • Triangle , VA • October 03, 2021
The repair was fairly straightforward. I used the enclosed door removal tools to remove the old door. Then I slid the new door into place. The whole process probably took 1 minute.
Read more
More
By: Ge
Part Number: WR09X10106
Refrigerator won't cool or compressor clicking? The overload and start relay protects and starts your compressor. DIY fix in 30-60 minutes.
Do-It-Yourself Stories from Customers like You
Overload was smoking Ken P. • Kent , OH • December 13, 2018
Replaced overload, and capacitor
Read more
More
By: Frigidaire
Part Number: 316580614
This assembly includes the spark ignition switches and wiring harness that control the igniter circuits on a gas range or cooktop. The switches detect burner position and signal the igniters to spark when a burner knob is turned. Replace this assembly if burners fail to ignite, click continuously without lighting, or if the spark module does not activate consistently.
Do-It-Yourself Stories from Customers like You
The back left burner didn't light and didn't click when turned the knob Oceanna C. • Watsonville , CA • April 07, 2016
My husband and myself didn't agree on which part was the exact problem. He felt it was the valve. I felt it was the ignitor/ orifice. And we both agreed the Harness-Ignitor needed to be replaced. So we ordered all 3, and I'm not sure if in fact all three were needed or not, but now with those parts replaced, the range is working like brand new!! Thanks to all the videos and diagrams on the website we were able to fix it ourselves easily. And the price was cheaper then other websites, also it...
Read more
More
By: Whirlpool
Part Number: WPW10330137
The Push Button Switch is an OEM part for Whirlpool washing machines. This part activates various functions and cycles on the control panel of the washer. The switch is designed to ensure responsive and reliable operation when selecting wash settings.
Causes of a bad push button switch can include wear and tear from frequent use, exposure to moisture, or physical damage from impacts.
Symptoms of a bad push button switch include:
Unresponsive buttons on the control panel
Inability to start or change wash cycles
Intermittent operation of washer functions
Error codes related to control panel issues
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer was humming when pushing start button Chris K. • N. Wildwood , NJ • May 28, 2017
Removed front of dryer panel, removed top, and removed drum. Replaced motor and wheel, because the old wheel was rusted on the motor shaft, and could not be removed, so I had to break it off. Replaced motor, and reassembled. Everything works now. I also replace the switch-Pb, because the start button was getting stuck.
Read more
More
By: Frigidaire
Part Number: A00055408
Fixes dishwasher leaking, error code i20, or pump that won't stop running. Monitors water pressure to control wash cycles. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Leaking dishwasher. Richard W. • Louisville , KY • April 20, 2020
Replace the pressure switch.
Read more
More
By: Ge
Part Number: WB24X10204
This microswitch senses the microwave door position and controls the safety interlock circuits. Replacing a worn switch restores proper start/stop behavior so the oven only runs when the door is fully closed.
Detects door open/closed status to enable or disable cooking Part of the safety interlock system that stops operation if the door opens mid-cycle Replace if the switch fails a continuity check or shows heat or terminal damage What's included: 1 microswitch
Disconnect power before service; microwave capacitors can retain a dangerous charge Note wire positions and move them to the same terminals on the new switch Ensure the door latch cleanly actuates the switch; test operation before reassembly
Do-It-Yourself Stories from Customers like You
Stopped working tripped breaker Roberto M. • Pembroke Pines , FL • March 08, 2019
By replacing the switches.
Read more
More
By: Whirlpool
Part Number: 8203534
Fix a burner stuck on high or that won't heat properly with this cooktop infinite switch. Restores accurate temperature control. 30-minute DIY repair.
Do-It-Yourself Stories from Customers like You
Failed dual element switch on whirlpool ceramic cooktop model #gjc3034gb0 Rodney S. • Kuttawa , KY • August 17, 2014
This cooktop has a dual element with an inner burner surrounded by an outer burner. The switch controls either the inner burner alone or both. The switch failed in that it would not operate the inner burner by itself, both burners would come on and only on high. On 8/14/2014 I replaced the failed dual element switch as follows:
• Turned power off to cooktop.
• Removed unit from cabinet.
• Removed metal edging and glass top.
• Removed screws holding switch panel access underside.
• Removed old...
Read more
More
By: Whirlpool
Part Number: WP74003122
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Element would stay on high even at lower settings why it would fail in the "high" mode is not a good design David M. • Suffield , CT • February 04, 2015
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element
Read more
More
By: Frigidaire
Part Number: 5304508629
Refrigerator won't cool or compressor hums but won't start? A failed start relay prevents the compressor from turning on. DIY fix in under 30 minutes.
Do-It-Yourself Stories from Customers like You
The power was still on but the unit no longer cooled Kimberly B. • Santa Ana , CA • March 09, 2018
We replaced the starter and relay. Unit is working properly. We saved over $150 by replacing the parts in question.
Read more
More
By: Speed Queen
Part Number: 202937
If your washer overfills, underfills, or won't advance cycles, the water level pressure switch may have failed. Takes about 10-15 minutes to replace.
Do-It-Yourself Stories from Customers like You
Broken pressure switch Carole Y. • Yakima , WA • November 06, 2019
Bought part from you and got a repairman to put it in. Darlene of your staff found part I needed. Nice lady! Repairman charged $82 to do a 10 minute job. Not your fault!
Read more
More
By: Frigidaire
Part Number: 316219004
Fix burners that won't spark or click constantly. This igniter switch wiring harness restores reliable lighting on gas ranges. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
One of my stove burners would not spark. Mike M. • Bound Brook , NJ • October 26, 2023
I replaced the switch/wire harness that connects to the gas valves.
Read more
More
By: Frigidaire
Part Number: 5304527841
The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.
Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.
Symptoms of a bad oven light rocker switch include:
The oven light failing to illuminate when the door is opened
The light remaining on even when the door is closed
An inconsistent or flickering oven light
The switch itself becoming loose, cracked, or non-responsive
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
1 of the 4 burners would not ignite with its own control Shane W. • Fullerton , CA • November 15, 2022
Removed & replaced igniter switch assembly. The hardest part was figuring out how to remove the range top...look up a YouTube video with your manufacturer and model number to see how to do it.
Read more
More
By: Whirlpool
Part Number: WP3405281
Dryer won't stay running after releasing start button? A faulty power relay is often the cause. This relay keeps the motor spinning consistently.
Do-It-Yourself Stories from Customers like You
Dryer motor would not stay in operation after releasing start button Gary P. • Wilton , NY • October 13, 2014
Googled the issue and was told to replace the motor relay. I ordered new relay form App. Parts Pros and it arrived in less than 2 days. After some relatively simple dis assembly of the dryer I replaced the relay. Dryer works fine now.
Read more
More