Power Small Engine Start Switch Parts
Genuine Lg part
By: Lg
Part Number: 6600JB3007K
Refrigerator light won't turn off when door closes? This door switch controls interior lighting based on door position. Simple DIY repair.
This part fixes the following symptoms
-
Light not working
-
Not dispensing water
-
Ice maker not making ice
See more...
Do-It-Yourself Stories from Customers like You
Lights on refrigerator stayed on. Sue L. • Boise , ID • July 05, 2020
Ordered 2 light switches and replaced them.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 318293825
If your burner won't turn off or stays on high heat, this surface burner switch restores proper temperature control. Straightforward 30-minute repair.
Do-It-Yourself Stories from Customers like You
My ceramic surface cooktop had a large burner that would stick in the full on setting regardless of the control position Hugh H. • Duluth , GA • August 01, 2016
I replaced the Switch for the burner. Works fine.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP37001136
This cycling thermostat regulates exhaust temperature by switching the heater on and off to maintain proper drying heat. Replacing a failed thermostat restores consistent temperatures, helps auto-dry timing, and protects against fabric-damaging overheating.
- Controls the heating circuit to maintain target drying temperatures
- Provides temperature feedback for accurate auto-dry operation
- Common symptoms: long dry times, very hot drum/cabinet or scorching odors, auto-dry not advancing correctly, or no heat if the thermostat fails open
- Typically mounted on the blower housing to sense exhaust air temperature
Includes: 1 cycling thermostat. Install notes:
- Disconnect power; for gas dryers, also shut off the gas supply
- Access the thermostat (commonly on the blower housing); remove the necessary panel(s)
- Transfer wires one at a time to the new thermostat and mount it flat against the housing
- Reassemble, verify clear venting/airflow, and run a test cycle
Do-It-Yourself Stories from Customers like You
Heat was too high Douglas S. • Mesa , AZ • May 17, 2015
I went ahead and ordered the element, and the 2 different thermostats not knowing exactly which one might be the problem. My My Maytag opens from the front and it was actually pretty easy to get into. Also gave me the opportunity to vacuum out the inside of the dryer. Pop the top off, remove the wires that connect the door switch (noting the colors and placement), take off the 2 inside nuts that hols the fron on, pull it forward and lift it off, 3 inside screws to take out to inside lint part...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9761048
If your dual burner is stuck on high or won't adjust temperature, this infinite switch is likely the cause. Easy DIY repair takes under an hour.
Do-It-Yourself Stories from Customers like You
Burner was stuck on high William M. • Mountaintop , PA • June 23, 2014
Replaced dual element switch.
Fixed the problem.
All is good
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 279782
Dryer won't start but has power and timer works? This belt switch kit stops the dryer when the belt breaks. Moderate DIY repair, 45-60 minutes.
Do-It-Yourself Stories from Customers like You
Broken belt switch Jack F. • Hermosa Beach , CA • July 08, 2016
Every time I tried to start our dryer, the "Sensing Light" came on, I heard a little "click," and the dryer would not start.
According to the very helpful Appliance Parts Pros. videos, I was able to dismantle, diagnose a few components, and discover the broken part. In this case, it was a Broken Belt Switch.
I ordered the part, we went on vacation for a week, and when we returned home the part was at our residence. The next day, I installed the part and all is good now.
I am nearly 70 years...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9762215
If your range burner won't respond to settings or produces erratic heat, this surface element infinite switch restores precise temperature control.
Do-It-Yourself Stories from Customers like You
Blew the oven switch! i hate it when that happens! Daniel F. • Miami , FL • July 18, 2015
First and foremost I UNPLUGGED THE OVEN!. I'll pass on the early morning SHOCK THERAPY! Second, I unscrewed aluminum protection plate from back of oven. Next, I unplugged the two connections behind the oven switch. Then I removed the plastic switch from the front and unscrewed the two screws that secured the oven switch to the oven. Once you've completed all these steps you take your new oven switch and do everything again but in reverse order. Hope this was informative, direct, and that your...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9763762
If your cooktop burner won't heat or won't adjust temperature, the infinite switch likely failed. This part regulates burner power. DIY repair in 30-45 minutes.
Do-It-Yourself Stories from Customers like You
Broken cook top switch Joseph M. • Scottsdale , AZ • January 27, 2015
Removed control panel and replaced broken switch. Much easier then expected.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10184148
Washer only fills with hot water or stops mid-cycle? The water temperature switch controls incoming water temps for proper cycle selection. DIY repair.
Do-It-Yourself Stories from Customers like You
Washer would not let cold water into the machine. Jim J. • Prosser , WA • March 12, 2014
I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me..
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10350906
Dryer won't start or stops mid-cycle? A faulty door switch prevents operation when the door position isn't detected. Moderate DIY repair, 30-45 minutes.
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134936800
If your washer won't start or the lid won't unlock, the lid lock switch may have failed. This DIY repair typically takes 10-15 minutes with basic tools.
Do-It-Yourself Stories from Customers like You
The locking mechanism would not release the lid had to break it to open Dennis H. • Bridgeton , NC • January 10, 2015
1) Ordered part.
2) Removed front panel by loosening the two screws at the bottom front.
3) Removed old Safety Switch/Lid Lock by disconnecting wires (plug and 2 female disconnects)
4) Reconnected all wires and reinstalled switch.
5) Replaced front panel.
6) Tested Unit.
7) FYI - I found that the locking mechanism stays locked until cycle completely finishes on its own. DO NOT force the cycle to end. Lid will NOT unlock.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3406653
This sensor harness connects the dryer's moisture sensor bars to the main wiring, helping the control or timer read moisture levels so Auto Dry cycles can advance and deliver consistent, reliable drying performance.
- Provides the electrical path between the moisture sensor bars and the control/timer
- Enables the dryer to sense wet fabrics and adjust or advance Auto Dry cycles
- A damaged or open harness can cause Auto Dry to not advance, run too long, or stop early
- Contribute to inconsistent dry times or a "Sensing" indicator that behaves abnormally
What's included: One sensor wire harness Install notes:
- Disconnect power before servicing
- Access the sensor bars at the front bulkhead; note wire routing and clip locations
- Transfer routing/clips from the old harness; connect to both sensor bars and the main harness plug, ensuring snug terminals and clear wire paths
- Restore power and run an Auto Dry test; inspect/clean the sensor bars and check harness continuity
Do-It-Yourself Stories from Customers like You
Dryer turning off on auto cycle with clothes still damp Mark F. • Topsham , ME • January 31, 2015
Replaced 3 low cost parts as advised by Appliance Parts Pros. Saved the labor costs by troubleshooting and replacing parts with their great videos. Works like new, and took 15 minutes to complete the repair.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10167742
If your range burner stays on high and won't adjust temperature, the infinite switch likely failed. This control switch regulates element power levels.
Do-It-Yourself Stories from Customers like You
Burners were working correctly most of the time but would stay in the on position (high )periodically and would not shut off automatically for the temperature you set the burner for Daryl B. • Gloucester , VA • August 12, 2021
Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304527842
The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.
You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.
Symptoms of a bad Range Switch Rocker include:
- The switch not responding when pressed
- Inconsistent or flickering performance of the heating elements
- Physical damage or looseness in the switch
- Intermittent operation or complete failure to activate the desired function
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The rocker switch for to adjust the size of the heating element for the stove broke as well as the rocker switch to adjust the oven light broke Benjamin G. • West Sacramento , CA • January 07, 2017
I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once...
Read more
More
Genuine Lg part
By: Lg
Part Number: EBD50964602
The Pressure Sensor is an OEM replacement part for LG dryers. This sensor monitors the airflow or pressure within the dryer, helping to regulate drying cycles and ensure efficient operation. By detecting blockages or changes in airflow, it plays a critical role in maintaining proper performance and preventing overheating.
Over time, the pressure sensor can fail due to wear, electrical issues, or buildup of lint and debris. Damage to the sensor or its connections can cause the dryer to operate inefficiently or stop functioning altogether.
Symptoms of a bad pressure sensor include:
- Dryer not heating properly
- Extended drying times
- Error codes related to airflow or pressure
- Dryer shutting off unexpectedly during cycles
This OEM LG part is also compatible with Sears/Kenmore dryers.
More
Genuine Ge part
By: Ge
Part Number: WB24T10071
The Switch Gas Valve is an OEM part for GE ranges. It is responsible for controlling the flow of gas to the burners, allowing them to ignite and maintain a steady flame for cooking.
Causes of a bad switch gas valve can include wear and tear over time, buildup of debris or grease, or damage from repeated use or accidental impact. These issues can hinder the valve's ability to regulate gas flow effectively.
Symptoms of a bad switch gas valve include:
- Burners not igniting
- Irregular or weak flame
- Gas odor near the stove
- Inconsistent burner performance
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
One of my gas range's was not igniting Mark M. • Centennial , CO • June 23, 2014
Bought this switch gas valve for the non-functional burner, and it cleared right up.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10441696
Burner won't regulate heat or stays on constantly? The infinite switch controls burner temperature settings. Most DIYers replace it in 15-20 minutes.
Do-It-Yourself Stories from Customers like You
Bad burner control Larry T. • Rose Hill , KS • May 14, 2018
Replaced the control that I think was bad from the purchase of the stove new as the burner didn’t throttle as is does now.
Read more
More