Grinder Blade Parts

• Will not tumble
• Takes too long to dry
• Noisy

I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website. Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

• Ice maker dispenses too little ice

This was a little more involved than I originally thought, but after watching the video on the site it wasn't so bad. They walk you through each step verbally and visibly so you can see exactly what to do. Replacing the auger took around 20 minutes, and only that long because the screw holding the ice shield was a bit tough to turn. I just applied gentle pressure and turned slowly until it became loose. The rest was fairly easy, but I did get a small cut from the ice crusher blades. Nothing... Read more

I watched the video that you provided and the repair went very smoothly. The video was specific to the exact part that I purchased. Great instruction and easy repair! Read more

This was easier then I made it. Originally took the actual ice maker out without removing the whole system from the door. There are 3 silver screws that do that hold the whole mechanism in place, as opposed to the 5 white screws that hold the ice maker in place. With the entire assembly out it was a matter of routing the ground wire, retaping the wires, and then the whole assembly went back into the door without a problem. Need a phillips and a flat screwdriver, I also found a needle nose... Read more

• Ice maker dispenses too much ice
• Ice maker not making ice

Since I could not find the correct thermistor from the schematic provided, I ordered the thermistor harness for the evaporator. I cut the harness and spliced it to the sheared thermistor wires on the roof of the freezer compartment. It now works fine with a little "farmer ingenuity" help. Samsung was absolutely no help at all, but the guy that I spoke with over the phone at APP sure was. This site is now my "go to" for appliance parts! Tip for others with this model. Do not overfill the upper... Read more

It was after 11:00 at night a few nights ago, I couldn't sleep listening to the whining of the fan in the freezer, it was running and making noise sounding like waaoooww, waaaoww. It also sounded like grumbling of a garbage disposal. The refrigerator fan motor was so noisy it was keeping me up all night going on and off running really loud and about to fail. So I was desperate, and called AppliancePartsPros when I couldn't get to sleep near midnight because the fan was so noisy and Bud in... Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

Just bought the whole assembly and slid it in. Read more

After ordering the part, I first watched the video several times. Then I placed my phone on my workspace so that I could start and stop the video when following the step-by-step instructions. Then I shut down the refrigerator circuit breaker while I removed the ice container and full ice maker components. I then closed the refrigerator doors to keep the cold air in. I kept starting and stopping the video as I went, as I unplugged wiring components, connection jumpers, the ice maker shutoff... Read more

Ordered a new filter. Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

• Ice maker dispenses too much ice

Replaced ice maker. Some confusion as to which part # it was as the model number cross reference shows the one I purchased was not for my model refrigerator when it actually was. Secondly, a few comments from others said the switch out was simple. Only 3 screws holding in the ice maker although one of the three was in a tight spot . That is technically true. Three screws do hold the ice maker on the door , however, you must also remove the door panel behind the ice maker to get to the wiring... Read more

• Ice maker dispenses too much ice

This appears to be a weak spot on these refrigerators; the left-door ice maker will stop making (or at least consistently making) ice. Instead, an ice dam is created, which builds up in the ice maker corridor, making even getting the slide-in bucket nearly impossible to remove. The ice also freezes up the ice making tray, which therefore cannot drop the ice cubes. Generally, two things may go wrong which lead to this issue. The first is the ice-making assembly; its electrical components... Read more

• Ice maker dispenses too little ice

When I first searched the AppliancePartsPros.com site for my specific model, the ice maker that appeared in the parts list was not for my refrigerator. So, I bought one from one of your competitors. It arrived and worked but produced ice even more slowly than my original unit, albeit at 0F. So, I went back to AppliancePartsPros.com parts list and browsed completely through it only to find another ice maker that did match mine. It was almost twice the cost, but after installing it, worked... Read more

Ordered a new screen and filter. While waiting for arrival, removed wax covered dishes. Carefully removed wax filled filter and screen cover. Stuffed paper towels in hole to absorb water and prevent wax from entering pump. Prayed ????wax had not entered pump. With plastic knife removed visible wax. Wiped out with paper towels. Used entire roll. Used hair dryer to melt remaining wax and wiped every inch of racks, wheels, glides, silverware holder, seal, floor and so forth. Oh yes I did. At 1:30... Read more