Keyboard Parts

I installed a new clock timer and overlay the job took only a few minutes and a very easy repair. Useful hint take a picture of your clock timer before you start to make sure all your wires are put back in the right order . Charles B Lafayette Tn Read more

I replaced the control board. Repair company wanted $395.00. I ordered the board for 140ish, 5 days later, 9 screws, 6 moduler plugs....working oven. The hardest part was pulling out the stove. Read more

Ordered a new Faceplate Graphics, removed old faceplate and installed new. Required removing control panel with switches and display, including 10 screws to get to the faceplate. Faceplate has glue on rim, so had to peel off old faceplate, remove residue, then put on new. Not difficult, but reaching to remove the screws was a little challenging in a small kitchen. Now unit looks brand new! Read more

The main control panel finally went out on our stove making it useless. With the diagrams on the web site I was able to find the exact replacement parts I needed. Ordering the parts was fast and easy. Within a few days the parts were delivered and within 10 minutes my stove was working like new. The parts were a fraction of what a new stove would have cost me. Read more

I went to the Appliance Parts Pros website and spoke with Shawn in customer service via the chat option. He was very helpful and suggested I order the thermostat for my stove. It arrived in about a week and I installed it the same day. It was a very easy install with the exception of the wiring harnesses didn’t match so I had to splice the wires together. It worked perfectly and now my stove is working like new. I really appreciate everything Shawn did to assist me and make this project much... Read more

Replaced the control board and panel. Read more

Looked for solution on YouTube, found the possible solution. Looked up part number on AppliancePartsPros. Ordered it came in two days. Took of back, removed old board. Put in new board. plugged it in. Put back together. Worked fine. 1 hour start to finish. Cost was at least 2/3rds less than a new gas range. Read more

• Touchpad does not respond

Replacing the switch membrane restored full function. Relatively easy. Had to pull stove out just a few inches to provide access to two side screws holding control enclosure. Then four screws on bottom edge just above oven door. Then a screw above each burner control. And one screw on the top edge at each corner (right screw additionally holding a ground wire). That allowed the structure to come out. Helper required to hold structure while I worked to unplug the old switch-membrane from... Read more

• Touchpad does not respond

I looked online for possible repair solutions when the range would not turn off. I found that the membrane switch goes bad on these models. I looked online for available parts and Appliance Parts Pros had the item in stock. I ordered and it was here the next day. After receiving the part, again, I looked online for how to replace the membrane switch and youtube video walked me through the steps. It took about an hour and now it works like new. Read more

I read about the particular error code on blogs online. Most people agreed that it was the keypad membrane that was not working. I have never done any repairs on an appliance, but YouTube had great videos of someone changing out that particular part. I could have ordered the part for less through an appliance supply store locally, but they did not offer any return option on electronics. I ordered through Appliance Parts Pros and they were very prompt in their delivery. I am thrilled to say... Read more

Ordered the parts from Appliance Parts Pros, received within 5 days and replaced parts in less than 30 minutes. No problem with getting correct parts and fast. Read more

I did the repair myself. Read more

Got a replacement real fast delivery from you and exchange it fast and easy Read more

A very common problem with the GE oven is the dreaded F7 error code. I purchased the control board as well as the keypad and replaced both. The error code could have been either part but since I saw a lot of grease, I chose to change out both even though I isolated the problem to the keypad only. By resetting the error first by hitting the clock button on the keypad, turning off the power,disconnecting the keypad, then turning back on the power if the code doesn't come back it's the keypad. ... Read more

So, this is a common problem, and the fourth time I have done this for someone in by neighborhood. Takes about 10 minutes, and requires very little skill. You simply unscrew the oven from it's mount points, pull it out a little bit, remove the four sheet metal screws holding the panel in place, unplug electronics, and plug the new panel in. Just did my neighbors with this one, too 8 minutes for the whole project. Kinda sad the original Whirlpool/Maytag/Jenn-air (they are all the same basically,... Read more

Ordered a new Oven Control unit and an Overlay (ours was punctured in a few places -- old and brittle). Opened the stovetop and removed some screws from the front control panel area. Followed the advice from Appliance Parts Pros' video to take a photo of the locations of all the connections on the old panel before removal -- that was an instrumental step to the success of this project! The whole job took just over an hour. Now the over controls and timers work like new -- because they are!... Read more