Power Strike Small Engine Start Switch Parts

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more

• Won't start

I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control. Read more

Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm Read more

Watched the attached video, then followed directions and installed the part ordered. Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

• No heat or not enough heat
• Too hot

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

• Takes too long to dry

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I watched your video and had it fixed in less than 1 minute! Read more

Unscrewed door latch and replaced it with the new door latch (1-2 min). Unscrewed outer plate from door lock assembly. Removed door lock assembly from its outer plate and unplugged wiring. Replaced with new door lock assembly, plugged back in, tightened some screws, double-checked alignment between latch & lock assembly was good and the project was done. Incredibly easy and saved about $150 not having a repair tech come out to fix it. Read more

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

Removed the lower rack, removed the lower wash arm, removed the lower coarse filter, removed fine filter ( still no tools require to this point). Removed two 1/4" head screws with nut driver to then remove float switch, unplugged float switch, plugged in new switch, reinstalled filter, etc. This is a 5 minut job! Read more

• Doesn't shut off
• Won't start

I watch the video on YouTube. And it went step by step on how to take it off and on Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more