Power Small Engine Start Switch Parts

I checked the continuity on the thermal fuse (which was blown) and knew that it needed to be replaced. This made me question why it blew (i.e. what caused it to fail). I checked continuity on the thermostat (high limit) as well as the thermostat for the element. Both passed a continuity test, so I removed the high limit thermostat to inspect it and could hear it rattling inside. This leads me to believe the spring inside had failed, so I replaced this thermostat as well. Put it back... Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more

• Doesn't shut off

Took out igniter module and porcelain was cracked. Replaced with ordered part and it worker fine! Read more

I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more

I replaced both the probe and temp control. The problem came in calibrating the new control, the instructions that came with control did not factor in a double oven, called back and talked to Michael at tech support and he found proper instructions, walked me through the process and sent me a PDF file with all information needed. I can't thank Michael and AppliancePartsPros.com enough for their service after the sale. I would definitely recommend and use it again. Read more

I replaced the switch. I ordered the switch on Friday afternoon and received it Tuesday. And that was standard shipping. Read more

Ordered a new safety thermostat. Installed it in 10 minutes and good as new. Thanks for your great trouble shooting and fast parts the repair was a breeze. Read more

I replaced both the large single element and the large dual element control switches. It appears the resistors were burning out. Problem seems to be fixed. Will know later when I do some simmering. Read more

• Takes too long to dry

Replaced timer and cycling thermostat. cycling thermostat was the problem. For some reason it wasn't getting the message to the timer needed to cycle the dial. Read more

• Too hot

Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more

Removed front and top panels of washer, removed old switch assembly. Then mounted and hooked up new switch assembly, put panels back on, turned on power and unit now works fine. Thanks for the quick delivery on the part...our total machine down time was only 36 hours. Biggest difficulty was getting the machine out of its position to work on it! Read more

It took a long time to determine the problem but eventually I discovered that the plastic bracket (latch hook) that held the three door-switches showed appreciable wear from repeated door openings and closings. This wear stopped the door from sealing properly and the door switch safety mechanism blew the line fuse. I replaced the worn bracket (AP6230612) as well as the plastic latch mechanism (AP4553585) on the door that engages this bracket (and of course the fuse too) and the microwave now... Read more

The compressor was very hot and did not appear to be running. You could here a relay click on and off 15sec cycle. repeating every 2 minutes! Bought a new overload relay too repair, plus a new thermal protection switch because it was cheap. Both parts are actually located on the compressor behind a plastic cover. Found part numbers for parts by searching the compressor number on google! $25 Repair............ Read more

• Will not stop filling with water

Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more

• Will not stop filling with water
• Will not fill with water

Replaced the water-level switch and hose. Washer works again, no overflowing since! Read more

Was set to pull the trigger on a new washer since this one was 10+ years old. Broke a $25 lid switch fumbling to get the washer open before I found the appliancepros video library. Once I got things apart the right way I was able to diagnose the problem in 5 minutes. Identified the $10 part needed. Got the $10 coupling and the $25 switch and had the washer working like new in 20 minutes. I'm pretty proud of myself.. not going to tell anyone about the $25 switch. Read more