Nut Damper Control Refrigator Parts

The basin would fill but would not agitate, there was no sound, no grinding noises, no sound of a motor running without agitation due to a broken belt. The basin full of water was able to drain if I advanced the timer to Spin. By playing around with the timer dial further, I could get every function of the washer to operate, at least partially. So, that said electrical problem to me. I assumed the trouble was either the safety switch at the back of the lid or the timer mechanism. Tested... Read more

I removed the burners, which were rusted and needed some tapping.They were pretty stubborn to remove from the insert. I removed the spark igniters, which were rusted where they screwed into the burner and then removed the venturi tubes.. Once this was done, I installed the new igniters to the underside of the new burner. I then installed the burners, which only took simple placement and a quarter turn to lock them in. I then hooked up the igniter wire to the new spark igniters. The repair... Read more

Replaced new motherboard and face plate. Read more

We followed the manufacturer's instructions about re-positioning the fan motor and installing the vent damper (easy). We constructed a duct system from the microwave to the outside of the house (challenging). We used 3.25" x 10" metal duct to start the system through the wall behind the microwave, where we added framing to reinforce a cut stud. We ran the duct up a closet wall and through its ceiling into the attic. We had to make an offset duct piece from 3.25" x 10" metal duct to clear a... Read more

• Freezer not defrosting

I had had the same problem 4 or 5 years ago and spent close to $200 to repair it. I did have the slip from that repair with part #'s so I went ahead and ordered a defrost timer and thermostat. You-tube had plenty of videos on replacing those parts and even before they arrived I was able to add a switch and bypass the broken thermostat and start a cycle manually with the timer. (which it seems was was still functional). Between that and cycling some ice packs up from the still working... Read more

I replaced the main control unit Read more

• Touchpad does not respond

I ORDERED A NEW CONTROLLER BOARD. THE DIRECTIONS SHOWED HOW TO UNCLIP THE OLD BOARD BUT THE FASTENERS WERE ON THE LEFT SIDE NOT THE BOTTOM AS INDICATED ON THE REPAIR INSTRUCTIONS. AFTER REASSEMBLY THE DISHWASHER FUNCTIONED AS NEW. THNKS FOR THE INSIGHT. Read more

Replaced "Ice Crusher Housing" and "Fixed Blades Spacer, both of which had broke. Read more

Ordered the part from Appliance Part Pros. It came in one day! Had to disconnect the gas line and wrestle the unit out of the wall cabinet, but the repair was easy and straightforward. The job took less than an hour Read more

So initial thought was bad bake igniter. I'bve replaced this before so I replaced it again and it wouldn't glow. Checked broil igniter and same thing, no glow. Checked voltage at molex connector for bake igniter and it went from 6.6v to 3.4v when triggered to glow -- well below the 120v expected. Ordered new clock/controller and overlay -- it shipped the next business day! Removed a handful of screws from the back panel to expose the clock/controller and removed/ replaced it with new... Read more

I don’t think I needed the capacitor and relay, but while I was at it I figured I would. Originally we found we had an issue when water cane out of the ice maker. The freezer was hovering around freezing and the refrigerator was about 33 deg. I unplugged the refrigerator and it came back on and ran about a day. The next night, same thing. This time cycling power did not seem to help. Removing the rear cover where the control board was and moving it around allowed it to turn on next time I... Read more

It's very easy fix. If your unit flashing e2 f2. It's your relay board take screw if on door couple latched s on the gray relay box pull wires harness of slow. Re install the same way it came of Just remember to cut the power off first . Leave your door open when re powering unit. Read more

Turn off power to machine, Take off door panel - 12 screws. hold up door panel a bit and make sure to remove the ribbon from the touch pad to the control module (use some pliers to rock it out of the board). Since I was changing the Module, I just removed the 1 screw that held it in place and it gave me some more room to get my hands in there and remove all the wiring freeing up the board to remove the touch pad ribbon last (I didn't want to tear it because I was not replacing it and after 9... Read more

It was easy, I got the model number of my dryer, then I went on google and found your website. You got a perfect diagram of the door of my dryer. After I saw the video relate it to my problem, I purchased the parts that I need it to fix it, I didn’t need my husband to do it for me. I gave him a surprise after he got home for work. It was all done. Thanks Read more