Run Vent User Control Display Board Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 216979600
Electronic control panel touch pad for upright freezers. Mounts on the front door. Replace if buttons are stuck, unresponsive, or the display is damaged.
Do-It-Yourself Stories from Customers like You
The alarm button was stuck. James B. • Eustis , FL • December 22, 2017
Replaced the control panel all fine.
Read more
More
$239.95
- Compare At:
-
$287.94
- You Save:
-
$47.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 316443919
This is a relay control board that manages the switching of electrical power to heating elements and other high-voltage components in the oven. It receives signals from the main control board and activates or deactivates the appropriate circuits. Replace this board if the oven elements fail to heat, heat intermittently, or if you notice error codes related to relay or heating circuit failures.
More
$365.95
- Compare At:
-
$435.48
- You Save:
-
$69.53
Genuine Frigidaire part
By: Frigidaire
Part Number: 316462807
This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.
Do-It-Yourself Stories from Customers like You
Kenmore Model 790 Electric Range. Would not get above 250 degrees. Had been taking increasing amount of time to pre-heat. Joseph N. • Abingdon , MD • April 04, 2014
Ohm'ed out the heat elements and both were good. Outlet had 240 volts. I had reviewed several items on the internet. Everything pointed to the control board. Ordered the part on a Sunday night using standard shipping and received it Tuesday. Replaced and tested. Over is working again.
Read more
More
$341.48
- Compare At:
-
$402.95
- You Save:
-
$61.47
Genuine Frigidaire part
By: Frigidaire
Part Number: 318022001
Fix an oven that won't heat or bake element not working. This relay control board receives signals from the main control board. DIY repair under 1 hour.
Do-It-Yourself Stories from Customers like You
Relay boards on both wall ovens were bad baking element on both ovens would not work Andy S. • Kingsport , TN • September 22, 2014
Andrew helped me trouble shoot the problem. First I replaced the elments but that did not fix the problem. When I spoke with Andrew he told me how to test the OHMS on the new and old element and they were both readying 26 OHMS. I then replaced the control panel for the clock and oven controls. This did not fix the problem. The next step was to replace the relay boards. We placed numbers on the wires (~30) to avoid confusion. Taking notes also helped. Replacing both relay swithces took...
Read more
More
$294.95
- Compare At:
-
$350.99
- You Save:
-
$56.04
Genuine Speed Queen part
By: Speed Queen
Part Number: 38881P
Washer won't advance cycles, keeps filling, or skips rinse/spin? Timer controls cycle sequences. Moderate DIY repair restores proper wash timing.
More
$182.95
- Compare At:
-
$217.71
- You Save:
-
$34.76
Genuine Whirlpool part
By: Whirlpool
Part Number: 8186394
Oven not heating, switches to broil instead of bake, or buttons unresponsive? The control board regulates bake functions and temperature settings.
Do-It-Yourself Stories from Customers like You
Oven control board. Ken L. • Blowing Rock , NC • December 15, 2023
Replaced the part.
Read more
More
$231.95
- Compare At:
-
$273.70
- You Save:
-
$41.75
Genuine Whirlpool part
By: Whirlpool
Part Number: W11736462
Cracked or damaged control panel trim? This escutcheon covers and protects control switches from grease and spills. Simple install, reuse screws.
Do-It-Yourself Stories from Customers like You
The compactor stopped compacting. Dennis S. • Sachse , TX • October 18, 2021
Replaced drive gear and power nuts.
Read more
More
$45.30
- Compare At:
-
$53.91
- You Save:
-
$8.61
Genuine Ge part
By: Ge
Part Number: WE19M1656
This control panel assembly replaces the white front console on your dryer. It restores a solid mounting surface for the timer, switches, or display so you can select cycles and settings with proper alignment and smooth operation. What it does
- Provides the front console housing for the dryer's user controls
- Keeps buttons/knobs and indicators aligned and protected
- Restores appearance after cracks, discoloration, or broken tabs
- Helpful when controls feel loose, are hard to press, or the console is rattling
What's included
- 1 white control panel assembly
Install notes
- Disconnect power; if gas, shut off the gas supply before servicing
- Remove control knobs and any end caps; take out mounting screws/clips and lift off the old panel
- Transfer any brackets, light pipes, clips, and harness retainers from the old panel to the new as needed
- Reinstall and tighten fasteners; refit knobs and verify smooth control operation before restoring power
Do-It-Yourself Stories from Customers like You
Front button had broken off Scott L. • Miramar , FL • March 13, 2015
Replacing the control panel assembly is extremely easy with one exception. To take off the existing panel (and there is no way to order a button for this, you have to order and replace the entire assembly), you pull the dial knob off (it comes right off, no tools required). There's a single screw underneath, Phillips head. You can then slide the panel up, and then unplug the cable connecting the circuit board to the dryer itself.
Next steps: Unscrew the half dozen or so screws to remove the...
Read more
More
$261.95
- Compare At:
-
$309.10
- You Save:
-
$47.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003410
Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.
Do-It-Yourself Stories from Customers like You
General overhaul of a 14 year old machine Todd F. • Wellsburg , WV • January 20, 2016
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to...
Read more
More
$50.57
- Compare At:
-
$60.18
- You Save:
-
$9.61
Genuine Frigidaire part
By: Frigidaire
Part Number: 137006000
Washer won't start, shows error codes, or cycles randomly? The main control board manages all wash functions. Moderate DIY repair with careful handling.
Do-It-Yourself Stories from Customers like You
Frigidaire gltf2940fs2 front load washer e90 error code Wayne A. • Tewksbury , MA • August 01, 2016
After first doing a Google/YouTube search, There was only one "hit" on my search results. Next I went to an appliance message board forum but after almost a week and more than a dozen views, no response was received. This is unusual. I've been on this board before with positive results. They also changed the "rules" for DIYers which could explain why I didn't have a lot of response from the experts.
I attempted to get the unit into diagnostics mode. I was unable to clear the E90 "general...
Read more
More
$232.95
- Compare At:
-
$279.54
- You Save:
-
$46.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 316441804
This is an electronic control board that manages the surface (cooktop) heating elements on an electric range. It includes a potentiometer and display panel that regulate element power levels and show settings. Replace this board if your cooktop burners fail to heat properly, cycle erratically, or if the surface element display is unresponsive or showing error codes.
Do-It-Yourself Stories from Customers like You
Old part cracked off so you could not use it William H. • North Fort Myers , FL • October 31, 2014
Part came in fast and was easy to put on. Turn off elect. and take front panel up , replace part and put back pannel.
Read more
More
$205.44
- Compare At:
-
$244.47
- You Save:
-
$39.03
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304502779
Refrigerator not cooling or ice maker stopped working? This main power control board manages core functions and power distribution. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
My fresh food compartment on my refrigerator was warm. Steven S. • Frederica , DE • April 17, 2020
After checking, I narrowed the scope to the evaporator fan and the main control board. I replaced the fan and still had the same issue, then I moved to the main board and that resolved my issue. It was a very easy job.
Read more
More
$228.48
- Compare At:
-
$269.61
- You Save:
-
$41.13
Genuine Whirlpool part
By: Whirlpool
Part Number: W11126319
This coin chute guides coins from the slide into the coin mechanism so the machine can register payment and begin a cycle. Keeping the chute intact and aligned helps prevent jams and misfeeds in coin-operated laundry equipment.
- Directs coins from the slide to the coin mechanism to register payment
- Helps ensure smooth coin drop, reducing bounce-back and misfeeds
- Common fix when coins jam, fall into the cabinet, or the unit won't start after payment
- Replace if cracked, bent, corroded, or missing
Install notes:
- Disconnect power; shut off gas before service
- Open the coin housing/slide assembly and retain existing hardware
- Install the new chute in the same orientation; align with slide and mechanism, then secure
- Test with sample coins to ensure proper drop and operation before returning to service
Do-It-Yourself Stories from Customers like You
The door latch was bad the control board and coin control board Christopher E. • Lansing , IL • May 18, 2016
A new set of control board, coin control board and the door latch was installed, and the washing machine was reprogrammed.
Read more
More
$178.95
- Compare At:
-
$212.95
- You Save:
-
$34.00
Genuine Ge part
By: Ge
Part Number: WB27X27461
Oven won't heat or display shows error codes? This electronic control board manages temperature regulation and oven functions. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Error code 8. Antonia C. • Glendora , CA • January 20, 2024
Replaced the oven control board.
Read more
More
$215.95
- Compare At:
-
$259.14
- You Save:
-
$43.19
Genuine Ge part
By: Ge
Part Number: WE19M1486
This replacement control panel, also called the backsplash assembly, is the structural console on the rear of the dryer top where the timer and switches mount. It restores secure control mounting and a clean, finished appearance when the original is cracked or damaged.
- Houses and supports the dryer's timer and control switches
- Covers and helps protect console-area wiring from contact
- Aligns control shafts through the panel openings for smooth knob operation
- Common signs of failure: cracked panel, broken mounting tabs, loose or rattling controls
What's included: 1 control panel Install notes:
- Disconnect power; for gas models, also shut off the gas supply
- Remove control knobs and mounting screws, then tilt or lift the console to access the panel
- Transfer timer/switches and any brackets from the old panel to the new one, keeping hardware organized
- Do not overtighten screws; verify all controls turn and click freely before restoring power
Do-It-Yourself Stories from Customers like You
Plastic console capture tabs and switch tabs broke plastic switch split Nelson T. • Mobile , AL • April 26, 2016
Unplugged the dryer. Disconnected the exhaust hose w/ 5/16" nut driver. Removed all knobs. Removed 3 Phillips head screws behind the console. Removed all switches and controls by lifting locking tabs and turning counter clockwise. Installed switches and controls into new console by inserting into hole(s) and turning clockwise until locking tab engaged. Positioned console capture tabs back in their slots and snapped console back in place with the back plate. Re installed the tree screws. Re...
Read more
More
$140.95
- Compare At:
-
$167.73
- You Save:
-
$26.78
Genuine Ge part
By: Ge
Part Number: WE4M353
Fix a dryer that won't advance cycles or turn on due to a worn timer shaft. This plastic-shaft timer restores knob grip and timing control. 10-minute DIY fix.
Do-It-Yourself Stories from Customers like You
Several parts timer belt doors with and element William F. • Gainesville , FL • August 09, 2015
Checked for the problem replaces that part along with some parts as preventive maint app made it easy parts for perfect and were shipped very fast app is the only place to buy parts great place
Read more
More
$129.47
- Compare At:
-
$152.77
- You Save:
-
$23.30