Hardware Hand Small Engine Fuel Cap Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3378138
The Dispenser Lid is an OEM replacement part for Whirlpool dishwashers. Located at the top of the dishwasher door, it provides access to add detergent and rinse aid to the internal dispenser compartment below. This dishwasher soap dispenser lid is included in the dispenser cover kit 4387043.
Causes of a bad dispenser lid can include wear and tear of hinge points from years of repeated openings. Cracks may also arise in the plastic material.
Symptoms of a bad Dispenser Lid include:
- Difficulty fully opening or closing the lid securely
- Leaks or spills occurring from around the sealing edges
- Potential cracks that compromise lid integrity or function
- Hinges that are loose or fail to support the lid in position
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Amana, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Soap dispenser lid spring wasn't opening lid Frank D. • Philadelphia , PA • December 22, 2014
I watched the video on your site and it showed step by step how to replace the spring. Excellent shipping time. Good customer service on chat forum.
Read more
More
$23.61
- Compare At:
-
$28.10
- You Save:
-
$4.49
Genuine Ge part
By: Ge
Part Number: WR17X22070
Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
12 y o rental unit ge side by side was missing parts and dispenser was non functional Scott M. • Asheville , NC • October 04, 2015
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping...
Read more
More
$14.49
- Compare At:
-
$17.24
- You Save:
-
$2.75
Genuine Whirlpool part
By: Whirlpool
Part Number: W10491985
The Range Screw is an OEM part for Whirlpool ranges. It is a small but essential component used to secure various parts and panels of the range. It is designed to fit securely into pre-drilled holes, holding components tightly in place.
There are a few factors that can lead to a bad Range Screw. Over time, screws may become loose or stripped due to frequent use or inadequate tightening. Accidental cross-threading or overtightening can also damage the screw or the surrounding components.
Symptoms of a bad screw may include loose or wobbly parts, rattling noises during operation, or difficulty in keeping components securely attached. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Oven door outer glass was broken Slydell B. • Cape Coral , FL • November 26, 2014
Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site.
Read more
More
$7.56
- Compare At:
-
$8.32
- You Save:
-
$0.76
Genuine Ge part
By: Ge
Part Number: WD30X10020
Roller bearing cage installs in the dishwasher rack track to support smooth gliding. Replace if cracked, broken, or causing the rack to stick or slide out.
Do-It-Yourself Stories from Customers like You
Instructions to replace wd12x10304 (ap4484666) roller bearings Richard L. • Webster , NY • February 18, 2016
I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least.
For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle!
Steps to fix:
1) Order 2 of these Roller Bearing Cage.
2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are...
Read more
More
$34.95
- Compare At:
-
$41.94
- You Save:
-
$6.99
Genuine Lg part
By: Lg
Part Number: ABN73019101
Allows water to flow directly to your dispenser and ice maker without filtration. Install when choosing not to use a water filter. Confirm fit by model.
Do-It-Yourself Stories from Customers like You
No problem did not want filter for filtered water Rahul P. • Anaheim , CA • November 06, 2017
Replaced filter with plug.
Read more
More
$24.68
- Compare At:
-
$29.62
- You Save:
-
$4.94
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304507354
Soap dispenser door won't open or latch is broken? This detergent dispenser assembly fixes dispensing failures. DIY repair takes 10-15 minutes.
Do-It-Yourself Stories from Customers like You
Rinse agent leaking from the dispenser Hal C. • Clarksville , TN • September 13, 2016
This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order.
Problem solved for less than the cost of a service technician's call!
Read more
More
$61.56
- Compare At:
-
$73.26
- You Save:
-
$11.70
Genuine Frigidaire part
By: Frigidaire
Part Number: A00130341
Fix a soap door that won't open or stay closed. This detergent dispenser releases soap at the right time during wash cycles. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Dish soap door wouldn't stay closed Brad D. • Orrville , OH • April 19, 2020
Started with a YouTube video, then this site. Between the two, fixed in about a half an hour.
Read more
More
$77.95
- Compare At:
-
$92.76
- You Save:
-
$14.81
Genuine Whirlpool part
By: Whirlpool
Part Number: W10815373
The Water Inlet Valve is an OEM replacement part for Whirlpool dryers. Located where the water supply line connects, it controls the flow of water into the dryer drum for steam cycles. Precise control is needed to prevent temperature fluctuations or flooding.
Causes of a bad inlet valve can include mineral buildup clogging water pathways, worn diaphragms allowing constant flow, or mechanical linkage issues.
Symptoms of a bad water inlet valve include:
- Steam cycles not activating or producing steam
- The dryer fails to stop water flow and overflowing
- Fault codes displayed relating to water input functions
This OEM replacement part is compatible with brands like Maytag, KitchenAid, and more.
Do-It-Yourself Stories from Customers like You
Water spray for refresh cycle on dryer stayed on even during drying cycle Janice V. • Royal Oak , MI • March 12, 2018
Ordered new valve. Easy installation. Saved a service call charge (-;
Read more
More
$98.33
- Compare At:
-
$117.01
- You Save:
-
$18.68
Genuine Whirlpool part
By: Whirlpool
Part Number: W10777162
The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.
Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.
Symptoms of a bad range screw include:
- Loose or unstable components within the range
- Difficulty in securing parts during maintenance or repair
- Visible damage or wear on the screw
- Parts becoming misaligned or rattling during operation
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Left door hinge would not allow door to close square to opening Jay R. • Clearwater , FL • October 19, 2019
Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem.
Read more
More
$7.56
- Compare At:
-
$8.90
- You Save:
-
$1.34
Genuine Ge part
By: Ge
Part Number: WR02X10668
The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.
Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.
Symptoms of a bad Temperature Sensor Seal include:
- Inaccurate temperature readings.
- Condensation or frost near the sensor location.
- Frequent cycling or unusual patterns in the refrigerator's cooling process.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Fresh food side temp display says 37 degrees but inside ff side measures over 40 degrees. John N. • Southlake , TX • February 03, 2018
This fridge has had a problem of ice building up around evaporator coil in fresh food side. Wife (she HATES this thing) says it's done this from day one; 10 years. GE guy says all these models do this and there's no fix for it, so we have clean out the ice periodically... Like the 1940s pre auto defrost.
Now with the issue of FF side temp too highi assumed the ice had built up around FF evaporator coil preventing proper cooling, but AppliancePartsPros.com suggested the FF temp thermistor may...
Read more
More
$11.71
- Compare At:
-
$13.82
- You Save:
-
$2.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10289690
Cracked or missing ice maker cover exposing internal components? This protective cover shields the ice maker assembly. Simple DIY install in minutes.
Do-It-Yourself Stories from Customers like You
Ice maker quit working Peter S. • Lawton , MI • October 29, 2015
Replaced icemaker and shutoff arm. Easy project.
Read more
More
$7.48
- Compare At:
-
$8.83
- You Save:
-
$1.35
Genuine Frigidaire part
By: Frigidaire
Part Number: 137554110
This is a grille cover that sits over the lint screen opening on the top or front of the dryer. It protects the lint filter slot and provides a finished appearance while allowing proper airflow during the drying cycle. Replace this cover if it is cracked, broken, or missing, which can allow debris to bypass the lint filter and reduce drying efficiency.
Do-It-Yourself Stories from Customers like You
Broken lint cover Scott T. • Long Beach , MS • July 19, 2025
Screwed it on. The order shipped out the same day, arrived fast and on time.
But I have to mention the customer service. The person helping me place the order was EXCEPTIONAL!!!! Very friendly and helpful. BEST customer service experience I’ve ever had. I was so impressed that I asked to speak to her manager. The manager was also exceptional. Very nice. I highly recommend this company.
Read more
More
$82.34
- Compare At:
-
$97.98
- You Save:
-
$15.64
Genuine Samsung part
By: Samsung
Part Number: DA61-03166A
Secures the glass panel over your refrigerator's crisper drawers. Replace if cracked, broken, or missing to restore proper shelf support and appearance.
Do-It-Yourself Stories from Customers like You
Broke the fixer cleaning the glass over the crispers bins Carl C. • Camden , NJ • November 16, 2018
Order a new fixer
Read more
More
$5.50
- Compare At:
-
$6.60
- You Save:
-
$1.10
Genuine Frigidaire part
By: Frigidaire
Part Number: 241733911
Protective cardboard or plastic cover that installs over the internal cooling system and wiring. Replace if cracked, torn, ripped, or missing.
Do-It-Yourself Stories from Customers like You
Needed a new cardboard piece for the back of the refrigerator (#89) Gertrude M. • Dania Beach , FL • August 30, 2020
I had to make a few different holes in the cardboard but it worked great!
Read more
More
$53.95
- Compare At:
-
$64.74
- You Save:
-
$10.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304509435
Replaces cracked, burned, or missing waveguide cover in your microwave. Protects the magnetron opening from food splatter and moisture damage.
Do-It-Yourself Stories from Customers like You
Broken waveguide cover Urdley S. • Staten Island , NY • July 04, 2014
Ordered the part and popped it back in. Shipping was extremely fast.
Read more
More
$23.95
- Compare At:
-
$28.74
- You Save:
-
$4.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3378134
Covers the rinse aid dispenser compartment on your dishwasher door. Replace if cracked, broken, missing, or won't stay threaded properly.
Do-It-Yourself Stories from Customers like You
Drying agent cap/lid was broken Prachi B. • Concord , CA • December 05, 2014
The drying agent lid was broken for a couple years now and our dishes would never dry completely. We finally decided to google for Kenmore parts and this website came up. Couldn't believe how easy it was. All we had to do was find the brand and model number and all the parts showed up on Appliancepartspros.com website. We scanned thru the list found the lid and ordered. It arrived within 2 days. Viola!!
Now we wish we had done this much earlier. Thank you for such a smooth experience.
Read more
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83