Line Hook Line Mover Regular Spring Parts

• Lid or door will not open
• Lid or door won't close
• Won't start

New inner drum and front and rear outer drum; although other parts worked, still replaced the bellow and clamp, new door latch, and cleaned the hoses. Washer works great. Just like brand new. Even though matching dryer works, I am going to clean it up and replace some parts on it also. Read more

Easy to fix just follow the video. Read more

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Door latch failure

Disconnect existing part and connect new one. Disconnect involved removing back cover around lock and electrical connector. Also had to remove rubber gasket. Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

• Door won't close

I just simply just take 2screws off and remove old latch off and replace new latch on. This is easy not that hard. Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

• Will not agitate
• Will not drain
• Won't start
• Timer will not advance

Ordered new lid switch and plunger. Watched help videos and installed new parts, Washer works like new. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

Replaced lint filter and door latch, but door switch was the answer. Works great! No video for this model but was able to view a similar one to follow. Read more

Followed instruction I saw on a you-tube video. Was quick and easy. Read more

First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more

• Door latch failure
• Will not agitate

After watching the video it was strait forward. Just Pull the screws pop the lid swap the springs "grease them" and put it back together. I would suggest that you have a person help you mostly has a second pair of hands. The lid was over rear springs and it will save you some expletives to have the extra body. I had worn out springs and the load kept becoming unbalanced during spin cycles I just happened to coincide with the Lock mechanism failing. The motor drive for the lock stopped working.... Read more