Bath Fan Switch Parts

Remove and replace Read more

FIrst, I removed the cardboard cover on the back, exposing the compressor compartment. I noticed the fan was not moving. I touched the blade and it immediately started spinning, but not very fast. The compressor was getting hot, and I think prob. overheating. The fan stopped after a few hours and then "froze" solid the next day. I got the parts and I followed the process in the video to replace the fan. VIdeo was right on the money. but there were some difficulties. The retention clip on the... Read more

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

REPLACED THE LIGHT/LAMP SWITCH. Read more

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

Removed the back cover to access the fan area. Clean the area with brush and vac first. Unplugged the Refrigerator. Used a socket set with 1/4" socket. Had an extended and a standard socket. Removed the condensate plastic drain from the bottom of the refrigerator to have more access to the fan. Unplugged the fan motor. Removed the two screws holding the fan in place. Removed the fan unit from the condenser side of the bracket. Place new fan on the fan and installed exactly the way I removed the... Read more

• Noisy
• Freezer section too warm
• Fridge too warm

Replace evaporator fan motor located in freezer compartment Read more

Replacement fan assembly with motor Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

The LG Model LG Washer model WM2487HRMA ISSUE: Washing Machine was filling very slowly. Overnight it would fill about 1 or 2 gallons. I would clear the tub by pushing a) Power b) set spin to None c) push Start. That would empty the tub. REPAIR SOLUTION: That did not solve the problem. Second, I replaced both the single (1) Water inlet valve assembly Part Number:5220FR2006H and also the Water Level pressure switch Part Number:6601ER1006E That solved the problem. I can't tell you which... Read more

• Won't start

I am so blessed. I went online. Found the brackets. Watch the video for the brackets I chose. And lucky me. I did not have to pull the dishwasher out. The installer did not have it flush under the counter. So I was able to pull the dishwasher forward unhook the damage brackets and insert the new. Put the dishwasher back in. Two screws. Now the balanced and secure dishwasher washes better than ever and I did not have to pay an extraordinary fee for a repairman. I'm 68 and take care of a 72 year... Read more

I replaced the Blower Wheel Assembly. Read more

• Won't start

Got the model number off the dryer. Looked it up online. I wanted name brand replacement part. Found this wonderful AppliancePartsPros.com. Looked up my model number, went to top control panel section, ordered the Start Switch. In ONE DAY I received it. Removed the back part of my dryer. Easily removed the broken part. (I did watch a video online). Put on the new Start Switch. Instead of ordering a new knob. I removed a knob from the dryer that I don't use. It turns a buzzer on or off to let... Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

I removed the front panel of the dryer and the metal cover over the blower wheel. Removed the lock ring and clamp. Removed the old wheel and placed the new wheel on the shaft. I thoroughly cleaned all the lint around the area and inside the front cover. I resealed the metal cover over the blower and reinstalled the front cover. Dryer works great. Easy fix, I spent more time thoroughly cleaning all the lint. Read more