Float Switch Float Parts

• Will not fill with water

Ordered new inlet water valve and float switch kit. After repairs it now works fine. However the water inlet valve outlet end for fill hose (not water source) and wire connections (supposedly for this unit) were oriented 180 degrees opposite. I had to gently remove the blue plastic valve off the metal support bracket and turn it around and press back in place. Fortunately it appears it was designed for either orientation. Also the solenoid had to be unclipped and also rotated. Again it was... Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

Check fan operation and was OK. Everything else worked except when microwave was started for a cycle. I looked around on internet and found someone had trouble with the door switches. I started to check door switches and found one shorted. I replaced both lower door switches and it took care of problem. Read more

Replaced the two door switches. Read more

1) Unscrewed the metal pieces behind the switch panel. You'll notice 3 screws. Afterwards, I realized that I just needed to remove the screws to the left and right of the switch box. The box then slides out. If you take out the third that connects the box to the wire cover, just remember to screw that back in before you replace the box. 2) To make sure I didn't place the wiring in the wrong place, I basically took the wiring out one by one and placing it into the new switch. 3) Place the new... Read more

Thanks, I’ follow the instructions on YouTube and my repairs was completed. Read more

Went on YouTube and found out how to replace switch. Had it replaced in no time. Read more

I had the original sensors in my Frigidaire, which were now about 18 years old. The water dispenser would work, but I would have to push in the lever and then draw it back until it found that "sweet spot." I finally got annoyed enough with the problem that I looked online. I almost purchased the dispenser actuator (the paddle), and glad I didn't because it was not the problem. Unless your lights are out, or it broke, the culprit will be these little dispenser switches which get pressed... Read more

• Won't start
• Doesn't stop at end of compacting cycle

Original part was not available. Did some cross referencing and found s similar part Read more

Switches needed to be replaced. Make note of where each screw comes from. They were not all the same. To remove the front panel and get to the switches, you have to partially remove the cook top. Removed 5 screws from the back to release the cooktop. Slid the cooktop back far enough to expose screws holding on the front panel. Removed 4 screws from the top and 6-8 from the bottom (opened the oven door to get to the bottom screws). Removed screws from the front panel holding the switch in... Read more

I'm a 56 year old divorced woman. I started doing these kinds of repairs to save some money and honestly, to see if I could. So yes, if I can do it, it's not that tough to do. My microwave is built in above the stove - getting it down and back up was the hardest part of the job. An extra pair of strong hands really helps-for anybody, not just a 56 year old woman. The actual repair was pretty easy. Most likely problem was pretty obvious after a little research. Easy to take off cover, get... Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

This was a difficult problem to diagnose. Because the machine would start the wash cycle then shut down after a few minutes of running, it appeared that the cause might be a bad thermostat or heating element, but all checked out ok. That led me to believe that the control panel may be the culprit but it also appeared to be working correctly when I ran the diagnostics program. A visual examination of the components found that the door switch electrical connections looked discolored, so I removed... Read more

1) Unscrewed the metal pieces behind the switch panel. You'll notice 3 screws. Afterwards, I realized that I just needed to remove the screws to the left and right of the switch box. The box then slides out. If you take out the third that connects the box to the wire cover, just remember to screw that back in before you replace the box. 2) To make sure I didn't place the wiring in the wrong place, I basically took the wiring out one by one and placing it into the new switch. 3) Place the new... Read more

Simple replacement back to cooking Read more

• Element will not heat

My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more