Pump Parts

Replaced the pump drain assembly Read more

I started looking at new dishwashers and was quickly disheartened with the cost of these simple machines. There's really not much to them and yet they're so much money for what they do. I popped off the pump and took a look at it and cleared some "gunk" and hair out but it didn't fix the issue. Jumped on AppliandPartsPros.com and ordered the pump on a Friday night and had the part in hand Tuesday night after work. Took about 10 minutes total (dishwasher out and back installed, literally in... Read more

I also noticed one of the two water recirculation outlets near the front door was no longer spraying water. When I took it all apart, I found that these two tub water recirculation outlets are both connected to the pump.. one was clogged. The impeller on the drain pump was no longer spinning with the motor.. looks like it was worn on the inside.. when I took the pump apart it was full of scale. I could have just ordered the motor...but I figured I would replace the entire assembly as I also... Read more

I've had to repair this appliance before, and it's almost always the motor-pump that needs replacing. It's a pretty easy fix if you have a roll out dishwasher. All you have to do is flip the dishwasher on its back, unhook the pump (no tools required, just push down the locking tab and twist and disconnect the wiring), and plug in the new one. I noticed that the tub wasn't draining completely either, so I replaced the drain pump as well just to be on the safe side. If, as I did, you let this... Read more

I had clogs before, so I knew this wasn't the case. When I tried the "rinse and hold" setting, the water would fill, but no sound when it tried to drain. I suspected the pump. Searching through YouTube, I found a helpful video for the GE Profile unit. In fact, the video directed me to this site for parts. It seemed simple enough to replace and I verified the part number to order. I pulled out the dishwasher, laid it on it's side, swapped the part, put it back in, and tested. It now works... Read more

I had a repairman in to check why machine had no power. I watched as he opened the door up and secured the electrical ribbon in place and lights on control panel came on. Asked him questions about the noise he confirmed it was the blower. would have charged me around $250.00 to replace that. Spoke to a rep on the phone and ordered the part for $100.00. The replacement part arrived in 1 day. Looked at the parts diagram on your site to orient myself. Separated the the front door( screws)... Read more

• Not drying dishes properly

The solenoid that opened the air vent for drying was broken so it was open during the wash cycle allowing water to escape into the air duct. Found the part at SearsParts and AppliancePartsPro, and Sears was $15 more expensive. I ordered on Friday from AppliancePartsPro and selected standard shipping and the part arrive the next day (Saturday). Amazing service. AppliancePartsPro will be my first stop in the future. Read more

In the How to fix it your self section of Questions and Answers, your answers for removing the Base Spray Arm is incorrect. It states "just stick a screw driver into the base spray arm from inside the tub and turn", that does not work. Their are 2 tabs that in gauge the base spray arm with the tub. A 4 prong round wrench is required to insert from the bottom into the pump connector and turn the nut that sits inside. Read more

I used youtube to look for diagnostic and then took my washer apart all of a sudden the front loader was no longer fun, I cleaned out the trap that was full checked all other lines and put back together. After putting back together the door would not lock because one of the connectors was loose. I say this to remind you to check all the connectors. Jumping forward take apart put back together. Tested failed would not drain still. Looked for pump everywhere and found you guys. I was buying... Read more

Watched a video to see how to replace it Read more

Dishwasher failed to run normal cycle. Would fill and then empty, but would not run through the normal rinse/clean cycle. Determined that the Sump/Motor Assembly needed to be replaced. Dishwasher had to be pulled out to access part. Was difficult to snap into place and had to maneuver several times to get a tight seal before reattaching peripheral components. Ran a one-hour cycle to test for leaks and efficiency before reinstalling unit under counter. Read more

DIY, changed motor and sump. Put a dab of valve lubricant on seal. Wet outer seal of sump to get it to seat in bottom of tub. Cleaned electrical connectors corroded by leak. Coated connectors with dielectric grease. Had to buy additional clamp. Two clamps came in the sump package but both fit the smaller hose only. Neither fit the large hose. I wish the correct clamps were included. Home improvement store clamp is a little too wide to fit between ridges in large hose. Read more

Replaced the pump and spray arm Read more

• Noisy

Diagnosed the problem. The pump motor needed to be replaced. Took model number and looked part up on Appliance Parts Pro site and found the exact part. Ordered part with next day delivery . Part arrived as scheduled. Simple installation. Works like new. Thanks. Read more