Hardware Hand Small Engine Ignition Coil Parts

• Element will not heat

This repair was on a GE glass Cooktop range. This range has two indicator lights, a Burner On light, and a Hot Cooktop Light. The problem I was having was, the Hot Cooktop stayed on all the time (24x7), even when the cooktop surface had been off for hours and was cold. YouTubes that I viewed were all misleading on this symptom. They all pointed to the switch, which is the fix for the Burner Light staying on, not the Hot Cooktop Light staying on. I figured it out by going to the schematic.... Read more

• Little to no heat when baking

I visited Appliance Pros website and indicated the problem we were having etc. Found the suspected part (heating element), went on YouTube and found out how to remove the part from the oven and test it with a multi-meter. Keep in mind I have never used a multi-meter before or made repairs to an oven before. However, I have used Appliance Pros before to fix a refrigerator problem just a month earlier and after watching their video it was a very easy repair. Anyway, I tested the old convection... Read more

Replaced the oven heating element Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

First replaced defrost timer. Iced up again after 2 weeks. Then replace the defrost heater. So far so good. Read more

• Little to no heat when broiling
• Element will not heat

Replaced it. Read more

I replaced the bake element in the bottom of the unit. Read more

I ordered a new one Read more

Going on line and viewing your website, you provided a very easy way to get me to a picture that was exactly what I wanted with the exact (old style) connections. I had previously gone to Home Depot twice, and I still did not get the correct burner that I needed. Your website was great, I should have gone there first. I used the part that I received from AppliancePartsPROS.com and replaced the defective, old and non-working surface element. It was easy, I used a screw driver to snap off a... Read more

Ordered the conversion kit Read more

• Frost buildup
• Doesn't shut off

I have had the unfortunate problem of fixing this previously, so knew what to order. I ordered the defrost sensor and heater... and replaced both. Honestly, all I needed was the sensor I did and ohm test and got 0 on it... meaning it was bad, but just in case I replaced the heater. The fridge works great now, but I would suggest if this is your first time with this issue, remove the panel, unplug both sensors from the fridge, and do and ohm test while they are still in the fridge... and then... Read more

It only takes a screwdriver for this repair. Remove the two screws holding the old element, pull it out of the housing, making sure the wires attached to the element do not fall back into the housing when you unclip them. Once you reattach the wires, simply replace the two screws and the job is done. I could not reuse the old screws though since the old ones did not hold the tight (unit is 20 years old and they were simply stripped). I simply increased the thickness of the screws and the new... Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

Ordering the right part is the key. This is the element with 3 wire connectors NOT the usual kind with 2 prongs that slide in. Thank goodness this company carries these elements for old GE built-in stoves. I'm not super handy but replaced two in about 40 min. Make sure you save the old ceramic clamps. The three prongs of the element with connected wires need to fit completely in the ceramic grooves so the two sides can be clamped together. The new element comes with everything you need but... Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

• Element will not heat

Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more