Thermal Fuse Parts

I replaced the thermal cut-off sensors and the cutoff-Tml Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

• Won't start

I have a Jenn-Air microwave that didn't turn on and had no lights. It just stopped working completely. I unplugged the unit and had to remove the rear cover using a *security screw kit* that prevents people from opening the rear panel. Once opened, I removed the fuse and testing it with an OHM reader to determine that the fuse went bad. But I also had to determine why the fuse blew and noticed a sticky oily substance under the Capacitor. I used a rubber glove and needle nose pliers to... Read more

Replaced the thermostat and it turned on and I have power again. Read more

• Too hot

Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more

Replaced the high limit safety thermostat. Ordering was easy, and the part came quickly. The video on the web site was helpful, although I was not able to follow the instructions fully. Unless you have super skinny, long arms, you cannot reach under and around the dryer tub to reach the belt tension arm. I ended up having to remove the side panel of the dryer to remove the belt from the motor. Replacing the thermostat was simple enough. At this point, it seems to have corrected the... Read more

• Takes too long to dry

Replaced timer and cycling thermostat. cycling thermostat was the problem. For some reason it wasn't getting the message to the timer needed to cycle the dial. Read more

The wonderful parts pros on the phone said that it was probably the diode or the magnetron. So we tried the cheapest way first and it worked so happy to have my microwave back and working for only a few dollars rather buying a new appliance. Read more

Purchased a new sensor from AppliancePartsPros.com. Installed new part - Problem fixed. Read more

Unpluged dryer unscrewed vent hose used nut driver to remove back pannal then took flat head screw driver to bend tab on heating elment caseing and pry carefully the electrical conector away from elment conection to remove thermostat then i placed the new thermostat on tap and pushed elctrical conetion back onto heater element conection till everything was thight and didnt wiggle dryer works well now Read more

I replaced the thermostat. The bearing on the motor was getting loose, so I changed the motor to. The repair took about 2 hours. There are some good re[air videos on the parts web site. Read more

• Takes too long to dry
• Doesn't shut off

Changed Thermistor, Thermostats and the Thermal Fuse Assembly. I did not remove drum, so squeezing my hands in-between drum and vent hose pipe to remove screws was a tight fit, but doable. Read more

• Too hot

I replaced the main parts for the dryer cycle system Read more

We initially called a repair company who immediately diagnosed the fan, without opening up anything. They quoted $550 to repair. $159 of that was the fan part. Plus they told me the parts come from overseas and will take 2 week to arrive. I researched the model number and can part and found exactly what I was looking for on your site. Plus there were diagrams and forum discussions that boosted my confidence on repairing ourself. Using your parts diagrams and our manual information, we pulled... Read more