Agr5725sds Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

I have tried to remove the burner assemblies by removing the torx screws but they were badly rusted, and unfortunately they all were broken during removal. I just discarded the ruined orifices and assembled the new orifices and burner assembly. Read more

• Little to no heat when baking

The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more

Replaced It With New One Read more

Touch up paint Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

Replaced old igniter. also purchased new screws for burner and igniter assembly since old screws were corroded from spilled food/fluids etc over the years. made the installation much easier. If you need to replace a worn igniter, do yourself a favor and go to hardware store and get matching replacement screws or buy new with igniter. Now my front right burner lights every time with just a click or two. Very pleased. Read more

• Door won't close

Replaced the hinge and receiver. Read more

Had to drill out the portion of the old foot that was still in the grate. Cleaned out the opening. Popped in the new one and voilà- all fixed. I ordered 8 of the feet as I see this eventually happening to all of them. Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more