Chw9100lq Parts

• Will not drain
• Noisy
• Burning smell
• Pumps but will not spin

There was a loud noise from my washer during the drain cycle. (The washer seemed to drain just fine.) It was pretty easy to determine that the noise was coming from the drain pump. (Which for my washer is behind the front lower inspection panel on the right side front.) I inspected the outside of the pump for any physical damage and verified no issues with the pump or the mounts. Everything seemed ok. I then checked the drain pump filter(You will need something to catch water if you do... Read more

I contacted AppliancePartsPros and gave them my symptoms and failure codes and they were able to diagnose the problem and send the correct parts to resolve the issue. This is the 3rd or 4th time I've used their service since 2012 and they have been correct on each and every repair issue I've had. Many thanks for the professional advice and help! Read more

• Shakes and moves

We looked online at AppliancePartsPros.com under the symptoms and found it was most likely caused by the shocks. Of course there was a repair video showing how to replace all four shocks step by step, and there was a link for purchasing the four shocks at the bottom of the video. Our repair didn't go quite as quickly as on the video because we are novices, but we were able to do the repair ourselves and, once again, saved ourselves a ton of money! Now we have a very quiet washer and dryer again... Read more

• Lid or door won't close
• Lid or door will not open

I removed the two screws and all the pieces that were broken. Went online to Appliance parts.com, searched for the part using the model number from the machine and ordered the part . part arrived in 2 days and with a Phillips screwdriver was installed in less than 5 minutes. Read more

Watched a youtube video and it was easy to do. Read more

Followed your video instructions. It was invaluable. The toughest part was getting the seal on the back of the drum. Your technician made it look very easy. Once that was on, the rest was pretty easy. The control panel on my Whirlpool Duet washer had a holding screw at the bottom center of it. It wasn't shown in the video, but it was easy to figure out. If you are changing the boot, change the clamp as well. Read more

Touch up paint Read more

Replaced It With New One Read more

• Will not fill with water

Our original discussion with a parts rep. led us to change the control panel as we had tested the valves for continuity and had it. Changing the panel did not fix the problem. As we had power continuity, we then removed the hoses from the cold water valve and checked the flow. The wash fill side of the valve had only a trickle of water, so we ordered a new cold inlet valve and replaced it. Problem solved, washer working like it's new. Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

Removed the leaking hoses and seal. Installed the new ones. They all fit perfectly. The disassembly/reassembly of the washer took the most time. Read more

Took the old part off and fitted the new one. I used the old plastic ball from the old hose and it worked fine. Next time I would replace the original clamp with a 4 inch hose clamp. The original clamp is way tooooooooooo hard to put back on....with a different clip it would be a 10 minute job at most. Read more

Called a repair man after not being able to determine the exact problem. Narrowed it down to valves, level switch or mother board. Repairman took money for parts and then said he couldn't find them. Went online and found this site, ordered parts Monday, had them by Thursday noon. Had machine running by 1. Read more

• Leaking

Took off cover, installed new parts. Read more

First remove the back from the washing machine. Top of the machine came off simple. To replace springs, I took a crow bar but it on the right side underneath where one of the springs should be. Lift the tumbler up remove and replace the spring. Did the same thing to the other side. On the tumbling unit there are spaces for three shock absorbers. Mine only had one shock in the middle. I put two new springs, one in the front and one in the rear. Then I replaced the right side spring with two new... Read more

ORDERED IN DOOR LOCK FROM ApplianceParts .received part next day. ( Great delivery time!) went down and installed on my washer at the Laundry.Took about 15min to install. I had very little down time at my business. Read more