Alliance Parts

The Dryer Cylinder Belt is an OEM replacement part for Speed Queen dryers. It is a critical component that transmits the rotational force from the drive motor to the dryer drum, enabling it to spin during the drying cycle. This drum belt is approximately 99" long. This drum belt is flat and has 5 ribs and 4 grooves.

Symptoms of a faulty dryer cylinder belt include:

• The dryer drum not rotating or rotating intermittently
• Squeaking or grinding noises during operation
• Visible wear, cracks, or fraying on the belt

Causes of a bad cylinder belt can include normal wear and tear over time, exposure to high temperatures, misalignment or improper tracking, or physical damage from foreign objects or debris.

This OEM Speed Queen part helps maintain optimal washing performance on standard, heavy-duty, and commercial machines.

This dual water inlet valve kit controls the hot and cold water entering select top-load washers. Replacing a weak or leaking valve restores proper fill performance and helps prevent slow fills, wrong temperatures, and unwanted drips.

• Regulates hot and cold water flow into the tub during fill cycles
• Integrated inlet screens help trap debris from the water supply
• Failure can cause no fill, slow fill, incorrect temperature, continuous filling, or water seeping into the tub when off

• Disconnect power and turn off both water supplies before servicing
• Place towels and a container to catch residual water; relieve pressure at the hoses
• Note and transfer hose and wire connections one-for-one to the new valve
• Restore water and power, run a test fill, and check for leaks

This dual water inlet mixing valve controls and blends the hot and cold supply during the fill cycle. Replacing a failing valve restores proper fill rate and water temperature selection for consistent wash performance.

• Opens and closes to admit hot and cold water as directed by the control, creating the selected temperature
• Helps maintain proper flow to the tub/dispenser during fill
• Common failure symptoms: no fill or slow fill, incorrect water temperature during fill, water continuing to drip or flow into the tub when the machine is off, or leaks from the valve body
• Humming from the valve with little or no water flow due to internal failure or clogged screens

• Disconnect power and shut off both water supplies before servicing; relieve line pressure
• Place towels, disconnect hoses, and note hot/cold orientation; inspect/clean inlet screens
• Transfer any brackets/fittings from the old valve if required; connect hoses securely without overtightening
• Turn water back on, check for leaks, then run a fill test to verify operation

The Thermostat is an OEM part for SpeedQueen dryers. The thermostat monitors and regulates the temperature inside the dryer drum during operation. It is responsible for sensing the dryer heat and activating the heating element at the selected temperature setting.

Causes of a bad thermostat can include overheating over time, fluctuations in electrical current that may damage components, or impact damage.

Symptoms of a bad thermostat include:

• The dryer not heating up or heating unevenly
• Constantly shutting off due to overheating errors
• Inability to select desired temperature settings
• Premature ending of dry cycles

The Heater Assembly is an OEM replacement part for Speed Queen dryers. This component generates the heat necessary to dry clothes effectively, working in conjunction with the blower to distribute warm air evenly throughout the drum. It is essential for proper drying performance and efficiency.

Causes of a bad heater assembly include electrical failure, damage to the heating element, or issues such as lint buildup leading to overheating. Prolonged use and normal wear can also lead to the element burning out.

Symptoms of a bad heater assembly include:

• Dryer not producing heat
• Clothes taking longer than usual to dry
• Dryer shutting off unexpectedly due to overheating
• Error codes related to heating issues

This OEM part ensures compatibility and performance in Speed Queen dryers.

The Idler Lever Kit is an OEM replacement part for Speed Queen dryers. This kit includes the idler lever, which plays a key role in maintaining proper tension on the dryer drum belt. By ensuring the belt stays aligned and taut, the idler lever enables smooth drum rotation during the drying cycle.

Symptoms of a bad Idler Lever Kit include:

• A squealing or screeching noise during dryer operation
• The drum not spinning or rotating properly
• The belt appearing loose or slipping off the pulley

Causes of a failing Idler Lever Kit can include normal wear and tear over time, damage from excessive strain or overloading, or misalignment of the drum or belt.

This OEM Speed Queen part is also compatible with Alliance laundry equipment.

The Knob Assembly is an OEM component specifically designed for Speed Queen dryers. This assembly includes the control knob and integrated electronic components that allow for cycle and setting selection.

Causes of a defective knob assembly include normal wear of constantly rotated buttons, sun damage to exposed plastic knobs, and general use degradation of sealed electronic sensors over time. 

Symptoms of a bad knob assembly include:

• Knobs or buttons that do not select cycles properly   
• Faulty digital displays for time and settings
• Erroneous buzzers or error messages
• Unresponsive or stuck control functions

This OEM Speed Queen part is also compatible with products from American Dryer Corporation. Replacing the entire knob assembly restores full functionality to reliably control cycles on your dryer. Proper maintenance ensures long-term durability.
 

The Lid Lock Kit is an OEM part for Speed Queen washing machines. It is made up of lid lock components and mounting hardware that allow the washer lid to securely lock into place during operation.

Causes of a bad lid lock kit can include wear and tear over time, damage due to forced opening of the lid, or failure of the latching mechanism.

Symptoms of a bad lid lock kit include:

• The lid not latching securely during the cycle
• Difficulty or inability to open the lid
• Excessive vibrations or noises from an unlocked lid
• Potential safety issues if the lid inadvertently opens

This idler wheel and bearing assembly maintains proper tension on the drive belt so your machine runs smoothly and quietly. Replacing a worn idler can eliminate squealing and help restore consistent drum or tub rotation. What it does:

• Keeps the drive belt properly tensioned for reliable operation
• Low-friction bearing supports smooth, quiet belt tracking
• Helps prevent belt slippage and premature belt wear
• Addresses symptoms such as squealing/chirping, burning rubber odor, belt coming off or fraying, or a drum/tub that won't spin or starts then stops

• Idler wheel with installed bearing

• Disconnect power; shut off gas supply before servicing
• Access the belt path and tensioner; relieve belt tension to remove the old idler
• Install the new wheel/bearing assembly and ensure free rotation
• Route the belt per the model's diagram, rotate by hand to check tracking, then reassemble and test

The Drain Pump is an OEM part for Speedqueen brand washing machines. Located near the rear of the washer tub, the drain pump works to empty water from the machine at the end of each cycle. It functions through an electrical motor that activates a spinning impeller, forcing water through the drain hose. 

Symptoms of a bad drain pump include:

• Washer fails to fully drain or leaves standing water 
• Drain cycle takes an unusually long time to complete
• Loud grinding or rattling sounds coming from inside

Over time, a buildup of lint or mineral deposits inside the pump chamber can clog the impeller and reduce efficiency. Allowing water to sit for extended periods also promotes mold growth. Replace your drain pump today with this genuine Speedqueen part and restore full draining capability.
 

The Inner Door Bezel is an OEM replacement part for Speed Queen washing machines. It is a white plastic panel that mounts to the inside of the washer door providing structure and rigidity. The bezel acts as a backbone for attaching other door components like the door gasket, switches, insulation, and more.

Symptoms of a bad inner door bezel include:

• loose door components
• missing or damaged mounting tabs
• cracks along seams or corners
• uneven gaps around the door opening.

Causes of failure can be wear and tear from opening and closing the door thousands of times, exposure to cleaning chemicals or solvents over time, or physical damage from accidents.

The Pressure Sensor is an OEM part for Speedqueen commercial washers. It plays an important safety role by actively monitoring water levels and pressure changes within the washing machine. Located internally, the sensor communicates water level status to the control module.

Causes of a bad pressure sensor can include failure or degradation of electronic components over time. Damage from impact or liquid ingress may also cause sensors to malfunction.

Symptoms of a bad Pressure Sensor include:

• Erratic or inconsistent water levels during fills and drains
• Inability to detect rises or falls in water pressure
• Fault codes or error messages on the control panel
• Safety issues from unregulated water valves

The Idler Lever Assembly with Bearing and Wheel is an OEM replacement part for Speed Queen dryers. This assembly maintains tension on the dryer belt, ensuring it rotates the drum effectively during operation. It includes the idler lever, bearings, and wheel, which work together to support smooth and efficient drum movement.

Over time, the idler assembly can wear out due to friction, heavy use, or lack of lubrication. Bearings may seize, or the wheel can become damaged, leading to reduced tension and compromised dryer performance.

Symptoms of a bad idler lever assembly include:

• Squeaking or grinding noises during operation
• Drum not turning or turning inconsistently
• Dryer belt slipping or breaking prematurely
• Increased drying times or inefficient operation

This OEM Speed Queen part is designed to restore reliable performance in compatible dryer models.

This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.

This door catch assembly secures the door when closed so the machine can run. A worn or broken catch can keep the door from latching firmly, causing start issues or interruptions during a cycle.

• Engages with the door strike/latch to hold the door shut
• If worn or damaged, the door may not close or stay closed
• Can lead to the unit not starting or stopping mid-cycle when the door moves
• Helps restore proper door latching and safety interlock function

• Unplug the appliance before service
• Open the door and remove fasteners retaining the old catch
• Transfer orientation from the original part to the new catch
• Test door closure and operation before returning to service

The Roller Cylinder is an OEM replacement part for Speed Queen dryers. This component supports the dryer drum and enables smooth rotation during operation, reducing friction and ensuring consistent performance. Proper functioning of the roller cylinder is essential for maintaining the balance and efficiency of the dryer drum.

Causes of a bad Roller Cylinder can include natural wear over time, exposure to heavy loads that strain the rollers, or debris accumulation that affects smooth movement. Misalignment of the drum or poor maintenance practices can also contribute to roller failure.

Symptoms of a bad Roller Cylinder include:

• A thumping or rumbling noise during operation
• The drum wobbling or not spinning smoothly
• Visible wear or damage to the roller upon inspection

This OEM Speed Queen part is also compatible with Alliance laundry equipment.