Rs696pxg Parts

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I began by turning off the breaker. I then removed the screws securing the bake element. I immediately noticed only one side was wired and the other side was burned off. The wire for the burned off section had fallen through the hole in the back of the oven. I tried fishing it out to no avail. I removed two side trim screws, the side trim pieces, and two screws holding the built-in oven into the wall. I was able to slide the oven out and onto a square stool that was the correct height. I... Read more

• Oven is too hot
• Oven not heating evenly
• Little to no heat when baking
• Won't start

I have a Whirlpool RBS245PDQ12 wall mount oven. Gathering information from AppliancePartsPros.com resulted in two possibilities: The Thermal Switch or the Control Panel. Talking with Appliance Parts Pros led to testing the Oven Temperature Sensor. It's supposed to test at 1080 Ohms at 70 degrees Fahrenheit. Mine tested at 960 Ohms so I knew it was bad... I found the service manual on the top of the Oven on the left behind the control panel. It has values for testing (Ohms of resistance)... Read more

Ordered the replacement glass through AppliancePartsPros.com and it arrived the next day. Wow! There are three pieces of glass (four if you include the front glass panel on the oven door when it is closed) layered inside and in looking at the diagram I ordered #7 and #24 replacement parts. I figured while I was in there the oven glass looked stained and maybe I would want new glass. With that said when the glass arrived and my husband and I got the oven door off and apart, we realized I... Read more

• Little to no heat when broiling
• Element will not heat

Found a real cool Youtube video by AppliancePartsPro.com. I watched it and learned how easy it was to unhook and replace the part with proper care and precautions. It even included tips on critical steps so the wires won't slip back inside the hole and save you from hours of possible mistake. Then I ordered the part. It came the day after, then I replaced the part, meaning, I DID THE WORK! (My wife was so impressed- lol) Easy as pie... but we made and had a much nicer roast the day after.... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Touch up paint Read more

Replaced It With New One Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

I watched a YouTube video prepared by someone at Appliance Parts Pro. Then I did a live chat to get the part ordered. It came 4 days later and that night my husband and I fixed it. Awesome! Thanks Appliance Parts Pros! Read more

Ordered the new fan (blower) from AppliancePartsPros. It arrived 3 days later. Pulled the wall oven out of the wall, removed the sheet metal back and removed the noisy fan. Installed the new fan, reinstalled the sheet metal back, shoved it back into it's place, turned the power back on and viola!, much quieter. Read more

Contacted Ashlee in the Customer Service Department of AppliancePartsPro and she not only explained the return policy but help ensure that I ordered the correct parts for my Whirlpool oven. She was wonderful and it was truly great customer service. I will continue to do business with this company. Read more

• Little to no heat when broiling
• Element will not heat

Replaced it. Read more

Replaced it myself. Read more

We ordered the part and one extra screw(which we didn't end up using). If possible take door off your oven for easy access and have lighting source to see well. Taking part out was easy. Putting back in was more difficult because you have to match up two layers of parts in our oven. The broiler coil and the broiler shield above it. We used small craft clothes pins to keep wires from going behind the built in oven. We used a small diameter screw driver to match up holes before putting... Read more