Gb22hbrbww Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Gas smell
• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

My Tappan Range, which I paid a grand total of $65.00 for, and have been using since Katrina, (Katrina in 2005 is how we measure time in South Mississippi.) I live in an old house, and I am old, too. Last winter was the coldest I can remember, and my husband (older than I and far more hard-headed) used the oven like a heater. I read all user's manuals, because I use only used stuff, I can download the manuals or read them online, and it clearly stated in there NOT to use the oven as a... Read more

• Fridge runs too long
• Freezer not defrosting
• Freezer too cold
• Won't start

A bit of research on the internet indicated the most likely problem was with the defrost system. I found the service manual for the refrigerator and was able to determine that the defrost heater and thermostat passed the self test. The refrigerator would perform a forced defrost which resulted in a cold refrigerator. More research revealed that this particular refrigerator does not have a defrost timer, instead the defrost cycle is controlled via the Electronic Control board which is also... Read more

• Frost buildup
• Leaking

The drain tube for for the defrost cycle seemed to be blocked, so I googled the repair & it sent me to AppliancePartsPros. Obviously, there's a design problem with this model since many other people have the same issue. This tube is an upgrade on the original for my KitchenAid model (design flaw). Since installation 4 days ago, I have had no leaks - awesome! The video for installation of the new tube on AppliancePartsPros was excellent. Two additions to the video: 1) I used a hair dryer... Read more

• Door won't open or close

I ordered a replacement part...took the shelf out of the refrigerator and slid the new rail into place. It was quick, required no tools and it works perfectly! Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

• Noisy
• Fridge too warm

The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more

• Too warm
• Clicking sound
• Won't start
• Freezer section too warm

Thank you to everyone who entered comments, especially about the "Clicking" sounds when it was trying to turn on the compressor. I did not notice them at first, but then heard them and was confident that one of these parts (or both) had a problem. In my case, I have custom cabinets around the sides of the refrigerator and hardwood floors in the kitchen so I put down some cardboard when the rollers would need to go at an angle due to a center island in the way. (I would rather do this myself... Read more

Left new gasket on the table overnight so it could stretch out. Removed the door. Temporarily replaced it with plastic and tape. Pulled off old gasket. Cleaned surfaces with decreaser and wiped dry with paper towels and alcohol. Inserted new gasket. Replaced door. Read more

• Door won't open or close
• Door sweating
• Frost buildup
• Leaking

I followed a video to remove the inside door panel and gasket. Putting the new gasket was as easy as the video said. The only problem was ice had built up on the inside of the door panel that needed to be defrosted. Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

First, I watched your VERY HELPFUL videos showing exactly how to remove and assemble the parts. I removed the salvageable parts from the old shelf frame and reassembled it. Read more

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more