Inlet Water Pump Model Ce Parts

• Will not drain
• Noisy

It was fairly obvious that the washer drainer motor had failed, water was not draining, filter was clean (bottom lower left panel door, have a pail ready!) and drain line was not blocked. Someone had provided great advice on the Appliance Parts Pro's site about replacing the drain motor from the bottom. Great suggestion! Easy to do, although be prepared for more water to drain from the washing machine onto the floor after you lay it over. I carefully lowered the machine onto it's back,... Read more

• Leaks water
• Leaking
• Will not drain
• Fills and drains at the same time

After noticing a leak from the washer I got on YouTube and determined the likely cause was a bad drain pump. The repair looked easy enough, so I ordered a replacement part. Well.......the removal wasn't quite as easy as they showed on the video I watched. Supposed to slip right off after removing the retaining clips. Upon additional video reviews I saw that an old washer could have significant rust on the shaft onto which the pump is installed. And boy, did I have rust on my machine. I yanked... Read more

This was to address an E:09 fault code on a Bosch dishwasher. I swapped out the Circulation motor and heater assembly. The video given on APP.com was for a different model, but more or less the same. The video gave me confidence enough to order the part and attempt it. The significant difference was that in the video, the assembly is easily accessible from the bottom of the unit. On my unit, however, the bottom is a closed plastic pan that isn't easily removable, likely requiring removal of the... Read more

Leak was slow but becoming gradually worse. Pulled dishwasher out from under counter then visually inspected sump while it ran. As soon as the water got very hot, I could see the sump leaking where it meets the stainless pan. Searched for the correct sump gasket without success. Turns out that the gasket is built into the sump for this model. The built-in gasket is very narrow (under-engineered IMHO which is probably why it developed a leak). Thanks to Simon's excellent videos at... Read more

• Not dispensing water

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more

I spent a lot of time taking apart and cleaning the drain pump and hoses in my Bosch dishwasher. I still got the error that the drain pump wasn't right. So, after doing some research, I learned that the motor might be done and that seemed to be the only solution. I serached for my part on APPs.com and found the part for about $43 ($50 by the time tax and shipping was added in). The part was ordered, shipped and was on my doorstep in two days. I followed the repair video instructions provided... Read more

I opened the cover panel of the control board. I visually checked for burns on the board and verified all connectors were firmly seated. I opened the bottom of the unit, and I saw the service manual in a zip-lock bag. From this manual, I verified that the drain pump resistance is good, the start capacitor is good, and the lid switch is good. I entered diagnostic service mode. Persistent alarms are 4 and 25.Error 4 means Reset Monitor, while Error 25 means Pressure Sensor Dropout. I... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

I was days into researching new dishwashers when I stumbled upon a recommendation to check diagnostic codes (and where to find the tech sheets). After troubleshooting based on my dishwasher’s recommendations, including cleaning the filter of the original inlet/fill valve, I determined the part would need to be replaced. I was nervous when the replacement part arrived because even though it said it would fit my discontinued inlet valve, it looked different (angles of each connection); however,... Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

The original pump was getting jammed intermittently, more and more often. I cleaned it out, but that didn't help the jamming. So I ordered a new pump. Have your new pump on hand and look at it to see how it attaches. The original pump, a different part number than the replacement, lasted about 7 years of almost everyday use, with multiple loads each day. My washer model Maytag MHW5500FW0 has the pump at the bottom back, in an awkward position. This took me about 2 hours due to the awkward... Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Ice maker won't dispense ice
• Ice maker not making ice

By visiting your website, viewing the repair instructions and ordering the right parts. Very easy to understand and to do the repair.. Read more

Replaced pump. From the bottom. Tipped it back then got to pump from the bottom. Machine is heavy. Read more

• Ice maker dispenses too little ice

Ordered a new icemaker from appliancepartspros.com, now get this, I ordered the part at 4:33 on Friday 31 Oct'14 and received it the next day 01Nov'14 around Noon, had it installed by 12:30! Once again, OUTSTANDING service. Read more

The water just sat in bottom of the tub, but the dishes never got wet. The water would drain out at the end of the cycle. I took a chance that it was the circulation pump and not the control panel since everything else seemed to be working. I replaced the circulation pump &motor and the problem was solved. The hardest part was getting the DW out of the cabinet since it was a very tight fit due to the floor tile. The job of replacing the part only took about 15~20 minutes thanks to the repair... Read more

• Will not drain

I have a 12 year old Kenmore Elite washer. One day, suddenly, I heard a grinding noise and the washer abruptly stopped. I called a repair service and was told it could be the bearings in the drum of this front-load washer, or it could be the washer's drain pump, which automatically shuts down when the drain pump fails. The repairman said, if it is the drum, it wasn't worth fixing for the age of this washer. It would cost $85 for him to come out and diagnose the problem, then if I decide to fix... Read more