Keraz05pwh3 Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

When bake was set, the stove would function normally, it would show pre-heating then get up to temperature and beep twice like normal when it reached the set temperature. Shortly after it would start beeping and scroll “ fault detected, press start to try again” across the display. Pressing start did not resolve, the message would continue to post and the pizza inside was burnt. We noticed the broil element was glowing. This model stove does use the broil element for backing but it... Read more

• Oven is too hot
• Oven not heating evenly
• Little to no heat when baking
• Won't start

I have a Whirlpool RBS245PDQ12 wall mount oven. Gathering information from AppliancePartsPros.com resulted in two possibilities: The Thermal Switch or the Control Panel. Talking with Appliance Parts Pros led to testing the Oven Temperature Sensor. It's supposed to test at 1080 Ohms at 70 degrees Fahrenheit. Mine tested at 960 Ohms so I knew it was bad... I found the service manual on the top of the Oven on the left behind the control panel. It has values for testing (Ohms of resistance)... Read more

• Little to no heat when broiling

DISCONNECT CIRCUIT BREAKER!!!. Remove oven door. Remove two screws that attach the element to the back of the oven, and two screws that secure element to the oven roof, then remove element. Had to be careful that the four wires don't slip into the back of the oven (difficult) to keep them from falling back as they are very short. Remove and replace element. I should have also detached the temp probe as it gets in the way and is easily broken off its flimsy mounting plate. The hardest part is... Read more

I first diagnosed the problem by replacing the burner control (Infinite switch) with one from a smaller burner (one that I knew worked fine). That seemed to solve the problem. I ordered the correct control for the big burner on Saturday night, it arrived Tuesday and installed it in less than 10 minutes using only a Phillips screwdriver. Remember to unplug the stove before performing any service. Take this time to clean around and under the stove. (You know it needs it!) Read more

Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more

Replaced the blown heating element. I also only to be on the safe side, replaced the over temp sensor. I checked it with the meter when I pulled it out and it was ok. Tested ok. Thank you very much for the less than 2 day delivery on the part. Read more

I bought an( as is) range (Maytag) form a dealer. I assumed that it would have racks, however, it came without. I tried to find some racks that would fit but none available. So I decided to order from Appliance Pros and received the right racks two days after I ordered. Very Happy Camper, Read more

Replaced the switches. Read more

• Door won't open after self cleaning cycle
• Element will not heat
• Little to no heat when baking
• Won't start

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

I found the gasket on your website. I watched the installation video provided. I purchased the gasket and installed it. It was inexpensive and painless. I will order from you again. Thanks Roger Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more

• Element will not heat

Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

• Won't start

I was going to just throw my stove out and get a new one until I did some research. I stumbled onto this site and found my broken part watched a quick video thanks to this wonderful site, they convinced me I could do it. I ordered the part on a Saturday night and Tuesday I got my part I was shocked. Took 5 minutes to fix and this site saved me hundreds of dollars on buying a new stove. Would buy again from this site in a heart beat. Thanks appliance parts pros! Read more

Touch up paint Read more