Rmc257pvs01 Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Oven not heating evenly
• Little to no heat when baking
• Won't start

I have a Whirlpool RBS245PDQ12 wall mount oven. Gathering information from AppliancePartsPros.com resulted in two possibilities: The Thermal Switch or the Control Panel. Talking with Appliance Parts Pros led to testing the Oven Temperature Sensor. It's supposed to test at 1080 Ohms at 70 degrees Fahrenheit. Mine tested at 960 Ohms so I knew it was bad... I found the service manual on the top of the Oven on the left behind the control panel. It has values for testing (Ohms of resistance)... Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

Received new part less than 24Hrs from order placement, installed and operating normally 15 min later. GREAT SERVICE!! Read more

• Door won't close

Ordered the correct parts, which arrived in 2 days. Took a couple of hours as this sucker is a huge pain, but some offered tips did help. Second time these have broken on this oven.... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

• Little to no heat when broiling
• Element will not heat

Found a real cool Youtube video by AppliancePartsPro.com. I watched it and learned how easy it was to unhook and replace the part with proper care and precautions. It even included tips on critical steps so the wires won't slip back inside the hole and save you from hours of possible mistake. Then I ordered the part. It came the day after, then I replaced the part, meaning, I DID THE WORK! (My wife was so impressed- lol) Easy as pie... but we made and had a much nicer roast the day after.... Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more

Removed the Microwave from the wall, then had to almost completely disassemble the sheet metal surrounding the microwave unit itself. Lots of screws and wires to work around. Takes 2 people to remove the microwave and set it on a stand outside of the wall unit. Once you get to the light bulb, the replacement is easy, just very challenging to get to the light bulb. Read more

• Won't start
• Element will not heat
• Little to no heat when baking

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

Replaced it. It took over 4 months to get the part due to a lack of inventory. I initially ordered from another supplier who after several months sent an incorrect part. Shifted to AppliancePartsPros. They confirmed the inventory shortage and gave me a two-month delivery estimate. About a month into the wait, they provided an update. The next update was noticed. That the part had arrived and was being shipped. Part arrived on time. Correct part, well packed, took about a minute to unpack... Read more

Replaced It With New One Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Touch up paint Read more

I'm a 56 year old divorced woman. I started doing these kinds of repairs to save some money and honestly, to see if I could. So yes, if I can do it, it's not that tough to do. My microwave is built in above the stove - getting it down and back up was the hardest part of the job. An extra pair of strong hands really helps-for anybody, not just a 56 year old woman. The actual repair was pretty easy. Most likely problem was pretty obvious after a little research. Easy to take off cover, get... Read more

Ordered the new fan (blower) from AppliancePartsPros. It arrived 3 days later. Pulled the wall oven out of the wall, removed the sheet metal back and removed the noisy fan. Installed the new fan, reinstalled the sheet metal back, shoved it back into it's place, turned the power back on and viola!, much quieter. Read more

• Little to no heat when broiling
• Element will not heat

Replaced it. Read more